Garmin Echo 100 Instrukcja instalacji - Strona 3

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Wyposażenie morskie Garmin Echo 100. Garmin Echo 100 6 stron. Flush mount template
Również dla Garmin Echo 100: Instrukcja obsługi (13 strony), Szablon (1 strony), Instrukcja obsługi (10 strony), Instrukcja obsługi (21 strony), Instrukcja obsługi (20 strony)

Drukuj stronę

Installing the transducer on a trolling Motor

Do not cut the transducer cable. Cutting the transducer cable will void your

warranty.

1. Feed the 20 in. (50 cm) cable tie ➊ through the slot on the transducer

mount ➋, with the ridges of the cable tie facing up, until equal lengths

extend on both sides of the mount.

For use in cold water or in areas with heavy timber or debris, use a metal

4–5 in. worm gear clamp (not included) instead of the cable tie.

➌

2. Position the mount gasket ➌ on the curved top of the transducer mount.

3. Place the transducer mount against the body of the trolling motor with the

front of the transducer pointed away from the propeller.

4. Secure the 20 in. (50 cm) cable tie around the body of the trolling motor,

but do not fully tighten the cable tie.

5. Properly align the gasket between the transducer mount and the body of

the trolling motor, and tighten the cable tie.

If necessary, trim the excess cable tie.

6. Position the transducer so that it will be parallel with the bottom when

in use, tighten the 10-32 locking nut ➍ until it touches the mounting

bracket, and tighten

turn more (do not overtighten).

7. Use the supplied 5

in. (14 cm) cable ties ➎ to secure the transducer

cable to the motor shaft.

If necessary, fill the forward-facing portion (except the cable tie pocket)

of the transducer mount with sealant to avoid accumulation of debris.

8. Route the transducer cable to the installation location of the echo device

while taking the following precautions.

• Avoid routing the cable close to electrical wires or other sources of

electrical interference.

• Make sure that the cable will not become pinched when the trolling

motor is deployed and recovered.

echo Installation Instructions

Notice

➎

➊

➋

➍

Installing the Swivel Mount

1. Select a mounting location

(page

2. Prepare the swivel-mount base

3. Fasten the mount with the cables installed in the mount

without the cables installed in the mount

Selecting a Swivel-Mount Location

Select a location to install the swivel mount, while considering these

guidelines.

• The location provides a clear view of the screen and access to the keys on

the echo.

• The location is sturdy enough to support the device and the mount.

• You can route the cables either from under the swivel mount, or from

behind the device.

• The location is the appropriate distance from a compass

Preparing the Swivel-Mount Base Installation

Use pan-head screws or bolts when securing the swivel-mount base. Screws

or bolts with countersunk heads will damage the base.

1. After you have chosen the location to install the swivel mount

determine whether you will attach the mount to the surface using screws

or bolts, and choose the appropriate fastening hardware:

• To attach the base with screws, use self-tapping, pan-head wood

screws, either size #8 or a diameter of

appropriate drill bit for the pilot hole.

• To attach the base with bolts, use pan-head bolts, either size #8 or a

diameter of

in. (4 mm), with the appropriate washers and nuts. Use

a drill bit of the same diameter as the bolt.

2. Separate the swivel base from the mount.

3. If you plan to route the cables from

under the mounting surface, orient the

swivel base so that the pass-through

holes ➊ face the desired direction.

4. Using the swivel base as a template,

mark the pilot hole locations ➋.

5. If you plan to route the cables from

under the mounting surface, mark the

location in the center ➌.

6. Using the appropriate drill bit for the

hardware, drill the three pilot holes.

7. If you plan to run the power and transducer cables from under the

mounting surface, use a

in. (16 mm) drill bit to drill a hole through the

mounting surface at the location you marked in step 5.

3).

(page

3).

(page

4).

(page

Notice

in. (4 mm), with an

➋

➌

4), or

6).

(page

3),

➊