Garmin Fusion BB100 Instrukcje instalacji

Przeglądaj online lub pobierz pdf Instrukcje instalacji dla Wyposażenie morskie Garmin Fusion BB100. Garmin Fusion BB100 4 stron. Black box entertainment system with wired remote control
Również dla Garmin Fusion BB100: Instrukcja instalacji (12 strony)

Drukuj stronę

FUSION

BB100 Black Box

Entertainment System with Wired

Remote Control Installation

Instructions

Important Safety Information

Failure to follow these warnings and cautions could result in

personal injury, damage to the vessel, or poor product

performance.

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

This device must be installed according to these instructions.

Disconnect the vessel's power supply before beginning to install

this product.

Before applying power to this product, make sure it has been

correctly grounded, following the instructions in the guide.

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

When drilling or cutting, always check what is on the opposite

side of the surface.

You must read all installation instructions before beginning the

installation. If you experience difficulty during the installation,

contact FUSION Product Support.

Software Updates

For best results, you should update the software in all FUSION

devices at the time of installation to ensure compatibility.

Go to

www.fusionentertainment.com/marine

latest software. Software updates and instructions are available

on your device product page.

Tools Needed

• Phillips screwdriver

• Electric drill

• Drill bit (size varies based on surface material and screws

used)

• Rotary cutting tool or jigsaw

• Marine sealant (optional)

Mounting Considerations

In high ambient temperatures and after extended use, the

device enclosure may reach temperatures deemed dangerous

to touch. As a result, the unit must be installed in a location

where it cannot be touched during operation.

This device should be mounted in a location that is not exposed

to extreme temperatures or conditions. The temperature range

for this device is listed in the product specifications. Extended

exposure to temperatures exceeding the specified temperature

range, in storage or operating conditions, may cause device

December 2015

WARNING

CAUTION

NOTICE

to download the

CAUTION

NOTICE

failure. Extreme-temperature-induced damage and related

consequences are not covered by the warranty.

When selecting a mounting location for the black box device,

observe these considerations.

• The device must be mounted in a location where it is not

submerged.

• The device must be mounted in a location with adequate

ventilation where it is not exposed to extreme temperatures.

• The device should be mounted so the cables can be

connected easily.

• To achieve IPX3 water ingress protection and optimal heat

sink cooling, the device must be mounted on a vertical

surface with the connectors pointing downward.

• The device can be mounted on a horizontal surface, but such

positioning might not achieve IPX3 water ingress protection.

• To avoid interference with a magnetic compass, the device

should be installed at least 15 cm (5.91 in.) away from a

compass.

When selecting a mounting location for the remote control,

observe these considerations.

• The remote control must be mounted in a location where

there is at least 70 mm (2.75 in.) of clearance behind the

mounting surface and you can access the controls after it is

mounted.

• If you need to mount the remote control outside the cabin, it

must be mounted in a location well above the waterline,

where it is not submerged.

• If you need to mount the remote control outside the boat, it

should be mounted in a location where it will not be damaged

by a docks, pilings, or other pieces of equipment.

Mounting the BB100 Device

If you are mounting the device in fiberglass, when drilling the

four pilot holes, it is recommended to use a countersink bit to

drill a clearance counterbore through only the top gel-coat layer.

This will help to avoid any cracking in the gel-coat layer when

the screws are tightened.

NOTE: Stainless-steel screws may bind when screwed into

fiberglass and overtightened. It is recommended to apply an

anti-seize lubricant to the screws before installing them.

NOTE: Screws are included with the device, but they may not

be suitable for the mounting surface.

Before you mount the device, you must select a mounting

location and determine what screws and other mounting

hardware are needed for the surface.

Place the device in the mounting location and mark the

location of the pilot holes.

Drill a pilot hole for one corner of the device.

Loosely fasten the device to the mounting surface with one

corner and examine the other three pilot-hole marks.

Mark new pilot-hole locations if necessary, and remove the

device from the mounting surface.

Drill the remaining pilot holes.

Secure the device to the mounting location.

Mounting the Wired Remote Control

At the mounting location, use a 57 mm (2.25 in.) hole saw to

cut through the mounting surface.

Apply marine sealant around the cutout (optional).

Place the gasket on the back of the remote control.

Feed the attached cable through the cutout.

Place the remote control in the cutout.

Printed in Taiwan

NOTICE

190-01953-02_0A