Garmin FUSION XS Series Instrukcja instalacji - Strona 3
Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Wyposażenie morskie Garmin FUSION XS Series. Garmin FUSION XS Series 6 stron. Marine wake tower speakers
Również dla Garmin FUSION XS Series: Instrukcja instalacji (13 strony), Instrukcja instalacji (11 strony), Instrukcja instalacji (6 strony), Instrukcje instalacji (4 strony)
Drukuj stronę
LED Color
LED Wire Color
Blue
Yellow
Magenta
Cyan
White
Blue
Red and green
Red and blue
Blue and green
Red, green, and blue
3
Route the positive and negative wires, and connect them to a power
source (Connecting the LED Wires to Power, page 3).
Connecting
the LED Wires to Power
You must connect all 12 Vdc wiring to the LEDs to a 3 A fuse at the power-
source end of the cable. You should connect the positive(+) power wire to a
12
Vdc
power source through an isolator switch or circuit breaker to turn the
LEDs on and off. You can use the same isolator or circuit breaker controlling
the power supply to your stereo, which allows you to turn the LEDs and the
stereo on and off at the same time.
You should use 20 AWG (0.5 mm
2 )
or thicker wire to connect the LEDs to the
battery.
1
Route the positive power(+) and negative ground(·) wires from the LED·
wire connections to the battery.
2
Connect
the
negative wire to the negative(·) battery terminal.
3
Connect the positive wire to the positive (
+)
terminal through a 3 A fuse
and isolator switch or circuit breaker.
Speaker Information
True-MarineN
Products
True-Marine products are subjected to rigorous environmental testing under
harsh
marine conditions to surpass industry guidelines for marine products.
Any product that bears the True-Marine stamp of assurance has been
designed for simplicity of use and combines advanced marine technologies
to deliver an industry leading entertainment experience. All True-Marine
products are supported by the Fusion 3-year worldwide limited consumer
warranty.
Registering
Your Fusion Device
Help
us better support you by completing our online registration
today.
Go to
www.fusionentertainment.com.
•
Keep the original sales receipt, or a photocopy, in a safe place.
Cleaning the Speakers
NOTE:
When mounted correctly, these speakers are rated IP65 for dust and
water
ingress protection under normal conditions. They are not designed to
withstand high pressure water spray, which may occur when you wash down
your vessel. Failure to carefully spray-clean the vessel may damage the
product and void the warranty.
NOTICE
Do not use harsh or solvent-based cleaners on the speakers. Using such
cleaners may damage the product and void the warranty.
Clean all salt water and salt residue from the speaker with a damp cloth
soaked in fresh water.
2 Use a mild detergent to remove a heavy buildup of salt or stains.
Troubleshooting
Before you contact your Fusion dealer or service center, you should perform
a few simple troubleshooting steps to help diagnose the problem.
If the Fusion speaker has been installed by a professional installation
company, you should contact the company so the technicians can assess
the problem and advise you about possible solutions.
There
is no sound coming from the speakers
Verify that all connections from the source device and/or the amplifier
are connected correctly to the speaker terminals.
Installation Instructions
The system
lacks
bass or high frequencies
Verify
that the correct wire polarity is observed between the source and
speakers.
·
The wires should be connected positive to positive and negative to
negative.
Verify that the speakers are attached firmly to the mounting surface.
The audio
is distorted
Verify that the source volume is not too loud for the speaker, and reduce
the volume if necessary.
Verify that the panels surrounding the speaker on the vessel are not
rattling.
Verify that the source
device
and/or the amplifier are connected to the
speaker terminals correctly.
If
the
speaker is connected
to
an amplifier, verify that the input level of
the amplifier is matched to
the output
level of the stereo. For more
information, see the manual for the amplifier.
The LED lights will
not
turn on
•
Verify that all wiring connections are correct and tight.
Specifications
Max.
power (Watts)
RMS power (Watts)
Sensitivity
(1 W/1 m)
Frequency response
Recommended
amplifier
power
(RMS,
playing music)
Nominal voice coil diameter
Impedance
LED Supply Voltage (Sports Model
Speakers only)
LED Load Current at 14.4 Vdc (Sports
Model Speakers only)
Operating temperature range
Storage temperature range
Cone material
Tweeter type
Water and dust rating
Compass-safe distance
Dimensions
<D
@
®
223 mm (8
13 /
16
in.)
0 176
mm
(6
15 /
16
in.)
180 mm (7
1 /
8
in.)
1
Protected against dust and water ingress.
200W
50W
91 dB
80 Hz to 18 kHz
From 20 to 150 W
30 mm
4ohms
From 10.8 to 16 Vdc
0.15 A max. per color
From
O
to 50'C (from 32
to
122'F)
From
-20
to 70'C (from -4 to 158'F)
Polypropylene (PP) cone with cloth
surround
Aluminum dome
IEC 60529 IP67
1
31
O
cm (122 in.)
3