Garmin GPSMAP 527 Guide Odniesienie - Strona 32

Przeglądaj online lub pobierz pdf Odniesienie dla Wyposażenie morskie Garmin GPSMAP 527 Guide. Garmin GPSMAP 527 Guide 42 stron. Technical reference for garmin nmea 2000 products
Również dla Garmin GPSMAP 527 Guide: Instrukcja instalacji (12 strony), Podręcznik referencyjny (2 strony), Podręcznik użytkownika (28 strony), Informacje o produkcie (37 strony), Instrukcja obsługi (28 strony), Szablon (2 strony), Deklaracja zgodności (6 strony), Podręcznik konfiguracji (2 strony), Skrócona instrukcja obsługi (4 strony), Instrukcja instalacji (8 strony), Instrukcja obsługi (38 strony)

Drukuj stronę
Garmin GPSMAP 527 Guide Odniesienie
NMEA 2000-Certified Sensor Configuration Information
1. From the NMEA 2000 Devices list, select the GET 10 device.
2. Select an option:
• For most Garmin chartplotters, select
• For other Garmin marine devices, select
3. Select the number of the engine that the adapter is associated with.
4. Select Done.
Troubleshooting the Gauge Type
When connected to a gauge, the GET 10 adapter gauge type is set to auto Detect by default, and the adapter automatically detects the type of
gauge it is connected to. If the engine-tilt reading on a connected Garmin chartplotter or marine instrument changes with the engine RPM, the
adapter may be detecting the wrong type of gauge.
To test the gauge-type setting:
1. When the boat is not moving, put the engine in neutral.
2. Use the throttle to increase the engine RPM. If the engine-tilt reading changes with the engine RPM, change the gauge type.
To change the gauge type:
1. From the NMEA 2000 Devices list, select the GET 10 device.
2. Select an option:
• For most Garmin chartplotters, select
• For other Garmin marine devices, select
3. Select an option:
• To automatically detect the gauge type, select
• To indicate a one-coil gauge, select
• To indicate a two-coil gauge, select
4. Perform the gauge-type setting test.
Configuring the GET 10 Adapter if the Engine Tilt Calibration, Engine Number, and Gauge Type
Selections Are Not Displayed
Depending on the version of software loaded on your Garmin marine instrument, the specific configuration options may not be displayed on the
configuration screens.
To calibrate the engine tilt if the menu option is not displayed:
To use the GET 10 adapter, you must calibrate the tilt of the engine that the adapter is associated with.
1. Turn the boat ignition key to the On position (not Start).
2. From the NMEA 2000 Devices list, select the GET 10 device.
3. Select an option:
• For most Garmin chartplotters, select
• For other Garmin marine devices, select
4. Set the engine tilt to the full-up position. The engine tilt is at 100%.
5. Enter the following command: "ENGINETILT=100Done"
6. Set the engine tilt to the full-down position. The engine tilt is at 0%.
7. Enter the following command: "ENGINETILT=0Done"
To configure the engine number if the menu option is not displayed:
If your boat has multiple engines, you can indicate which engine each GET 10 adapter is associated with.
1. From the NMEA 2000 Devices list, select the GET 10 device.
2. Select an option:
28
Review
Engine
Number.
>
Config
Engine
Number.
>
Review
>
Gauge
Type.
Config
>
Gauge
Type.
Auto
Detect.
1
Coil.
2
Coil.
Review
>
Generic
Config.
Config >Generic
Configuration.
Technical Reference for Garmin NMEA 2000 Products