Fujitsu 8432884555871 Instrukcja obsługi - Strona 6

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Klimatyzator Fujitsu 8432884555871. Fujitsu 8432884555871 16 stron.

Drukuj stronę

3.3. Inserting batteries

Battery type: R03/LR03/AAA x 2
1
2
9
5
1
Pull the cover in the direction of the arrow and open it
until it is trapped.
2
Remove the cover.
1 Turn the remote controller over and push the back
side of the cover and remove the claws by curving
the cover.
2 Pull in the direction of the arrow while curving the
cover.
3
Put batteries as shown in the figure above.
4
Press this button as shown in the figure above.
Use the tip of a ballpoint pen or other small objects.
5
Press
to start clock setting.
(
6
Press
Sunday).
* By pressing
from a 12-hour to a 24-hour clock.
7
Press
to continue.
(
8
Press
Press the buttons to change the clock by a minute.
Press and hold the buttons to change the clock by 10 minutes.
9
Press
to complete the setting.
Be close to the indoor unit. If you press the button from a
distance, settings may not be properly sent.
10
Install and close the cover.
NOTES:
• Use specified type of batteries only.
• Do not mix different types or new and used batteries together.
• Batteries can be used about 1 year in ordinary use.
• If the remote control range noticeably shortens, replace the
batteries, and press
En-5
3
7
RESET
6
8
4
)
to set day of the week (Monday to
, the time indicator can be changed
)
to set the clock.
as shown in the figure above.

4. BASIC OPERATIONS

■ 3 steps to start operation
1. Press
to start or stop the operation.
2. Press
to select the operation mode.
The operation mode changes as follows.
(Auto)
(Cooling)
3. Press
to set the desired temperature.
The temperature changes by 0.5 °C increments.
Temperature setting range
Auto/Cooling/Dry
Heating
NOTES:
• In the Cooling mode, the indoor unit fan may stop from time to time
to perform Fan control for energy saving that enables power-saving
operation by stopping the rotation of the indoor unit fan when the
outdoor unit is stopped.
In initial setting, this function is activated.
To deactivate the function, refer to "7.3. Fan control for energy saving".
• In the Cooling or Dry mode, set the temperature lower than the
current room temperature.
• In the Heating mode,
- set the temperature higher than the current room temperature.
- at the beginning of the operation, the indoor unit fan rotates at very
low speed for 3-5 minutes.
- the Automatic defrosting operation overrides the Heating operation
when necessary.
• In the Fan mode, temperature control is not available.
■ Temperature unit switching
1. Press
until only the clock is displayed.
2. Press and hold
The current temperature unit will be displayed. (Factory setting: °C)
to switch the temperature unit. (°C ⇔ °F)
3. Press
4. Press
to finish the setting.
If you do not press the button for 30 seconds, the displayed
temperature unit will be set.

5. AIRFLOW SETTINGS

5.1. Fan speed setting

Press
to control the fan speed.
)
The fan speed changes as follows.
(Auto)
(High)
When
is selected, the fan speed depends on the operating
condition.
To increase the air cleaning effect, set the fan speed to High.

5.2. Airflow direction setting

For details of the airflow ranges, refer to "Airflow direction range".
■ Up/down airflow direction setting
Press
to adjust the up/down airflow direction.
)
■ Left/right airflow direction setting
Before you adjust the left/right airflow direction, make
sure that the horizontal louver has been stopped
completely.
Adjust two knobs of the vertical louvers by hand.
)
(Dry)
(Fan)
(Heating)
18.0 - 30.0 °C
16.0 - 30.0 °C
for more than 5 seconds.
(Med)
(Low)
(Quiet)
CAUTION