Fujitsu RSG36KMTA Instrukcja obsługi - Strona 13
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Klimatyzator Fujitsu RSG36KMTA. Fujitsu RSG36KMTA 16 stron.
Drukuj stronę
Step 3. Installing WLAN adapter
CAUTION
• Be sure to turn off the power supply of the air
conditioner when installing or removing this product
to avoid the risk of electric shock.
• Do not put fingers, sticks etc. in the connection part of
this product and the connection slot of the indoor unit.
Otherwise, electric shock or damage to the product
may occur.
• Do not standing on an unstable platform when
installing or removing this product to avoid injury.
1. Be sure to turn air conditioner off and to disconnect all the
power supply.
2. Open the intake grille.
3. Open the WLAN adapter cover until it snaps.
4. Plug the WLAN adapter into the connection slot of the indoor
unit in the direction as shown in the figure.
Label side
5. Close the WLAN adapter cover and the intake grille.
Step 4. Air conditioner registration (pairing of WLAN
adapter)
NOTES:
• Before starting this setting, reconnect the power supply of the air
conditioner and wait for 60 seconds or more.
• Check that the smartphone or tablet PC is linked to the access point
you are connecting the air conditioner. The setting will not work if it
is not connected to the same access point.
• To control 2 or more air conditioners with the same smartphone or
tablet PC, repeat the setup of the chosen mode.
Register the air conditioner by following the instructions on
)
)
the mobile app.
This operation manual describes only the setting procedure of the
remote controller.
When the registration is completed, [
will turn on.
] indicator on the indoor unit
For reference
<Manual connection mode>
Setting procedure of the remote controller
NOTE: If you do not press any buttons of the remote controller for 60
seconds, the remote controller display will return to the original
display.
1. Press
until only the clock is displayed
on the remote controller display.
2. Press and hold
on the remote
controller for more than 5 seconds.
will be displayed on the remote controller
display.
3. Press
.
4. Select
using
controller.
5. Press
.
The indoor unit enters Manual connection mode
and [
] indicator on the indoor unit will blink.
NOTE: If the registration is not be finished in several minutes,
Manual connection mode is canceled and [
turns off.
In this case, repeat the remote controller setting.
<Easy connection>
Setting procedure of the remote controller:
NOTE: If you do not press any buttons of the remote controller for
60 seconds, the remote controller display will return to the original
display.
1. Press
until only the clock is displayed
on the remote controller display.
2. Press and hold
on the remote
controller for more than 5 seconds.
will be displayed on the remote controller
display.
3. Press
.
4. Select
using
controller.
5. Press
.
The indoor unit enters Easy connection and
[
] indicator on the indoor unit will blink
(on/off = 1sec/1sec).
When the WLAN adapter find a connectable WLAN access point,
the blinking will become slowly (on/off = 2sec/0.5sec).
NOTE: If the connection to WLAN access point is not be finished
in several minutes, Easy connection is canceled and
turns off.
In this case, repeat the remote controller setting.
Temporary deactivation of wireless LAN
NOTE: If you do not press any buttons of the remote controller for 60
seconds, the remote controller display will return to the original
display.
1. Press
until only the clock is displayed on
the remote controller display.
2. Press and hold
on the remote
controller for more than 5 seconds.
will be displayed on the remote controller
display.
3. Select
using
controller. *
4. Press
.
[
] indicator on the indoor unit will turn off.
* If you want to activate wireless LAN again, select
on the remote
] indicator
on the remote
on the remote
in step 2.
En-12