2N EasyGate Pro Szybki start - Strona 2
Przeglądaj online lub pobierz pdf Szybki start dla Gateway 2N EasyGate Pro. 2N EasyGate Pro 2 stron. Umts gateway
Również dla 2N EasyGate Pro: Szybki start (4 strony), Szybki start (4 strony), Szybki start (4 strony)
Drukuj stronę
2N® EasyGate Pro Quick Start
Basic Functions
· The primary purpose of 2N® EasyGate Pro
(from now only 'Easy Gate') is to transmit
voice between a GSM network and an
attached FXO-interface terminal.
· You can establish data connections (GPRS,
CSD) and send/receive SMS in combination
with a PC.
· Models of EasyGate with fax converter can
transmit fax messages using analog fax
Group 3 or data using analog modem on
telephone line
Read the CD-ROM User Manual carefully to get familiar with all system
functions.
EasyGate supports GSM GPRS technology for data connection. The
connection speed and quality depend on the GSM provider, accessible
services, signal coverage and network status.
2N® EasyGate Pro Installation and Connection
· Proper Location
- Install EasyGate with respect to a good
GSM signal strength.
- Place EasyGate out of range of sensitive
devices
and
human
bodies
electromagnetic interference reasons.
- EasyGate is designed for indoor use. Do
not place it near heat sources and on
direct solar radiation. It may not be
exposed to rain, flowing water and
moisture, aggressive gas, solvents etc.
· Needed Accessories
INCLUDED IN THE BOX
· 1x 2N® EasyGate PRO device
· 1x power adapter (12V/0,5A DC)
· 1x magnetic antenna with cable (SMA)
· 1x antenna for direct connection (SMA)
· 1x PC-connection USB A/B cable
· 1x telephone cable
· 1x SMS sending input connector
· 2x screws with dowels
· 1x CD with manual and SW
· 1x Quick Start manual
NOT INCLUDED IN THE BOX
· SIM card
· Information on Internet connection from
your provider (APN etc.)
· Rechargeable batteries
· You
can
send
an
SMS
programmed
number
using
sending input.
· The battery backed-up EasyGate version
allows you to maintain your traffic even in
the event of power outage.
· Firmware for EasyGate can be updated
from www.2n.cz
· External Antenna Connection
Screw the antenna cord into the SMA
antenna
connector.
Tighten
antenna connector gently with your
for
hand, never use a wrench!
· SIM Card Installation
Slot for SIM card is placed on the
connector panel. Insert the SIM card to
the slot according to the picture and
make sure that the card is locked
properly.
Select
the
required
provider and SIM card services, such as
call forwarding, call barring, preferred
networks, SMS centre, etc. using your
mobile phone before inserting your SIM
card into EasyGate.
· Telephone Line Connection
EasyGate can be connected to any
FXO-interface
equipment
telephone set, answering machine, PBX
CO line...). EasyGate is equipped with
identification of calling party (CLIP) via
FSK and so it is advantageous to connect
a terminal that is able to display the CLI.
· Battery
backup type)
Insert
four
battery NiMh size AA into the covered
compartment on the back side of the
to
a
pre-
gateway. Refer to the compartment
the
SMS
label for proper battery placement and
polarity.
batteries only!
Do not activate the power supply until the antenna is connected to
EasyGate to avoid the GSM module damage.
the
PC (USB)
Indication LEDs
GSM
Power
supply
GSM
Network
Phone
line
(standard
Data
Signal,
battery
indicator
Detailed description is in manual on CD-ROM
By entering three wrong PINs you block the SIM card. Enter the PUK code
into your mobile phone to unblock the SIM card.
installation
(battery
· Mains
Switch On
pieces
of
rechargeable
EasyGate is 12V DC voltage powered.
Connect the attached power adapter
(12V/0,5A DC) to the power supply
connector. After connection, switch on
EasyGate with the power switch on the
Use
mentioned
type
of
right-hand side of connector panel.
2N® EasyGate Pro Connection Layout
SMS
input
Power adapter
Analog phone
IN: 110V/240V AC
(FXO interface device)
OUT: 12V/0.5A DC
1. Hook off the telephone and hear the
Blue light – mains supply
Yellow light – battery supply
PIN tone:
Blue flashes – logged out
2. Enter the PIN using DTMF and press
Blue light – logged in
for confirmation. Hang up the line to
No light – standby
cancel a wrong PIN.
Yellow flashes quickly – ringing
– line off-hook
3. If you hear the busy tone after a while
Yellow light – call
(a few seconds), the PIN has been
Flashes 2-3 times – fax or data
entered correctly. This PIN will be
connection over FXS (fax version)
entered
Green light – PC connected
Flashes quickly – incoming data
power up.
1x in 3s – data transmission
4. If you hear the PIN tone again after a
Signal strength indicator
while, the PIN has not been entered
After hook off before start of dialing
correctly. Re-enter the PIN.
– battery state
Supply
Connection
and
Switch ON/OFF
(Backed-up version only)
SIM
PIN Secured SIM Card
automatically
upon
every