Fujitsu PRIMERGY DX920 S3 Instrukcja obsługi - Strona 10

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Serwer Fujitsu PRIMERGY DX920 S3. Fujitsu PRIMERGY DX920 S3 14 stron.

Drukuj stronę

S26361-F3695-E10

Independent Channel Mode allows all channels to be populated in any order. No specific Memory RAS features are defined

Requires min 1 memory Module per CPU

S26361-F3695-E1

BIOS Setup factory preinstalled to this mode. One Rank is spare of other ranks on the same channel. Spare Rank is not shown in System Memory.

For effective capacity within a channel, please have a look below.

Supported for RDIMM / LRDIMM only.

1x per CPU

Requires min 2x 1R/2R or 1x 4R modules per CPU

S26361-F3695-E2

BIOS Setup factory preinstalled for max. Performance, LV memory might be set to 1.5V operation. Four identical memory modules

will be equipped in one memory bank to achieve highest memory performance. All four modules are active and full capacity can be used.

Multiple of 3 identical modules to be configured per CPU

S26361-F3695-E3

BIOS Setup factory preinstalled to this mode. Four identical memory modules are always equipped in one memory bank to use the

Mirrored channel Mode. Only two modules contain active data, the remain two modules contain mirrored data

Supported for RDIMM / LRDIMM only.

Multiple of 2 identical modules to be configured per CPU

Unbuffered Memory (UDIMM) no SDDC (chipkill) support

- one DDR3 unbuffered ECC mem. Module, 1.35V

Choose up to 6 order codes per CPU

2GB (1x2GB) 1Rx8 L DDR3-1600 U ECC

4GB (1x4GB) 2Rx8 L DDR3-1600 U ECC

Registered Memory (RDIMM) no SDDC (chipkill) support

- one DDR3 registered ECC mem. Module, 1.35V

No mix with any other types of memory modules possible

Choose up to 6x for 2R per CPU

For performance reasons, we do not recommend

6x per

to configure more than 8 DIMMs per CPU

CPU, max.

4GB (1x4GB) 2Rx8 L DDR3-1600 R ECC

2/3 modules

Registered Memory (RDIMM) with SDDC (chipkill) support

per channel

- one DDR3 registered ECC mem. Module, 1.35V

1333MHz supported with up to 2DPC (6 modules/CPU)

Choose up to 6 order codes per CPU

4GB (1x4GB) 1Rx4 L DDR3-1333 R ECC

8GB (1x8GB) 2Rx4 L DDR3-1333 R ECC

2 modules

Registered Memory (RDIMM) with SDDC (chipkill) support

per channel

- one DDR3 registered ECC mem. Module, 1.35V

1600MHz supported with up to 2DPC (8 modules/CPU)

at 1.5V

Choose up to 6 order codes per CPU

4GB (1x4GB) 1Rx4 L DDR3-1600 R ECC

8GB (1x8GB) 2Rx4 L DDR3-1600 R ECC

16GB (1x16GB) 2Rx4 L DDR3-1600 R ECC

Load Reduced Memory (LRDIMM) with SDDC (chipkill) support

- one DDR3 load reduced ECC mem. Module, 1.35V

Choose up to 6 order codes per CPU

16GB (1x16GB) 4Rx4 L DDR3-1333 LR ECC

32GB (1x32GB) 4Rx4 L DDR3-1333 LR ECC

Independent Mode

Rank Sparing Mode Installation

Performance Mode Installation

Mirrored Channel Mode Installation

Effective Memory capacity / Rank Sparing Mode, 1 Channel populated

UDIMM

2GB

1DPC

2DPC

Minimum one memory module or order code per CPU = first memory

S26361-F3694-E613

S26361-F3694-E614

S26361-F3695-E614

S26361-F3696-E614

S26361-F3696-E615

S26361-F3697-E614

S26361-F3697-E615

S26361-F3697-E616

S26361-F3698-E616

S26361-F3698-E617

Fujitsu PRIMERGY Server

System configurator and order-information guide

PRIMERGY BX920 S3

RDIMM

4GB

8GB 2R 16GB

4GB

12GB

24GB

Note 1.)

Max. DDR3 memory speed depends on the memory configuration

(No of mem modules per channe) as well as on the CPU type.

The memory channel with the lowest speed defines the speed

of all CPU channels in the system, also for the channels of the

second CPU if configured.

For real memory speed (depending on memory type / population),

please check the spreadsheet "Memory speed" below

new due to supply

Mix of memory modules is only possible within the same group

Status: 2013-12-30

LRDIMM

16GB

32GB

12GB

24GB

28GB

56GB

10 of 14