Indesit I6G52/UK Instrukcja obsługi - Strona 3

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Piekarnik Indesit I6G52/UK. Indesit I6G52/UK 16 stron. Cooker and oven

Indesit I6G52/UK Instrukcja obsługi
The legs* fit into the slots on
the underside of the base of
the cooker.
Installation of the cooker
The appliance can be installed next to furniture units
which are no taller than the top of the cooker hob.
The wall in direct contact with the back panel of the
cooker must be made of non-flammable material.
During operation the back panel of the cooker could
reach a temperature of 50°C above room
temperature. For proper installation of the cooker,
the following precautions must be taken:
a ) a ) The appliance can be placed in a kitchen, dining
a ) a )
a )
room or bedsit, but not in a bathroom.
b )
b )All furniture around the appliance must be placed
b )
b )
b )
at least 200 mm from the top of the cooker,
should the surface of the appliance be higher than
the worktop of this furniture. Curtains should not
be placed behind the cooker or less than 200 mm
away from the sides of the appliance.
c ) c ) Any hoods must be installed according to the
c )
c ) c )
requirements in the installation manual for the
hoods themselves.
d )
d )
d )
d )
d )If the cooker is installed beneath a wall cabinet,
the latter must be situated at a minimum of 420
mm above the hob. The minimum distance
between the worktop and kitchen units made of
combustible material is 700 mm (Fig. A).
e ) e )
e ) e ) The wall in direct contact with the back panel of
e )
the cooker must be made of non-flammable
materials.
f ) f ) f ) f ) f ) The cooker is fitted with a safety chain that must
be attached to a hook, secured to the wall behind
the appliance.
! Some models can have their gas connection
inverted. It is important to make sure the safety
chain is always situated on the side which
corresponds to the hose holder (Fig. B).
HOOD
600
Min.
mm.
Fig. A
Fig. B

Gas connection

T he cooker should be connected to the gas-supply
by a corgi registered installer. During installation of
this product it is essential to fit an approved gas tap
to isolate the supply from the appliance for the
convenience of any subsequent removal or
servicing. Connection of the appliance to the gas
mains or liquid gas must be carried out according to
the prescribed regulation in force, and only after it is
ascertained that it is adaptable to the type of gas to
be used. If not, follow the instructions indicated in
the paragraph headed "Adaptation to different gas
types". On some models the gas supply can be
HOT PARTS
pressure regulators that conform to the regulation in
force. The gas supply must be connected to the left
of the appliance. Be sure that the hose does not
pass through the rear of the cooker touching hot
parts.
! Make sure the supply pressure conforms with the
values shown in the table entitled "Caracteristics of
the burners and nozzles". When the cooker is
installed between cabinets (recessed), the
installed between cabinets (recessed), the
installed between cabinets (recessed), the
installed between cabinets (recessed), the
installed between cabinets (recessed), the
gas connection must be effected by an
gas connection must be effected by an
gas connection must be effected by an
gas connection must be effected by an
gas connection must be effected by an
approved flexible hose with bayonet fitting
approved flexible hose with bayonet fitting
approved flexible hose with bayonet fitting
approved flexible hose with bayonet fitting
approved flexible hose with bayonet fitting
(BS 669 Current Edition). The gas inlet for
(BS 669 Current Edition). The gas inlet for
(BS 669 Current Edition). The gas inlet for
(BS 669 Current Edition). The gas inlet for
(BS 669 Current Edition). The gas inlet for
the cookers is a threaded G 1/2 gas female
the cookers is a threaded G 1/2 gas female
the cookers is a threaded G 1/2 gas female
the cookers is a threaded G 1/2 gas female
the cookers is a threaded G 1/2 gas female
f i t t i n g .
f i t t i n g .
f i t t i n g .
f i t t i n g .
f i t t i n g .
Connecting the gas supply
To make the connection, a flexible hose should be
used corresponding to the current gas regulations
which are:
• the hose must never be at any point in its lenght
in contact with the "hot" parts of the cooker;
• the hose must never be longer than 1,5 metre;
• the hose must not be subject to any tension or
torsional stress and it must not have any
excessively narrow curves or bottlenecks;
• the hose must be easy to inspect along its entire
length to check its condition;
• the hose must always be in good condition, never
attempt to repair.
connected on the left or
on the right, as
necessary; to change
the connection, reverse
the position of the hose
holder with that of the
cap and replace the
gasket (supplied with
the appliance). In the
case of connection to
liquid gas, by tank, use
When the cooker is
When the cooker is
When the cooker is
When the cooker is
3
GB