Indesit K3E51/EU Instalacja i instrukcja obsługi - Strona 4

Przeglądaj online lub pobierz pdf Instalacja i instrukcja obsługi dla Kuchenki Indesit K3E51/EU. Indesit K3E51/EU 23 stron.

Drukuj stronę

The following instructions should be read by a qualified

technician to ensure that the appliance is installed, regulated

and technically serviced correctly in compliance with current

regulations.

Important: disconnect the cooker from the electricity when

making any adjustement, maintenance operation, etc.

Positioning

The appliance can be installed next to furniture units which

are no taller than the top of the cooker hob. For proper

installation of the cooker, the following precautions must be

taken:

a) Kitchen cabinets installed next to the cooker that are taller

than the top of the hob must be situated at least 200 mm

from the edge of the hob.

b) Hoods must be installed according to the requirements

in the installation manual for the hoods themselves and

in any case at a minimum distance of 650 mm.

c) Place the wall cabinets adjacent to the hood at a minimum

height of 420 mm from the hob (see figure).

d) Should the cooker be installed beneath a wall cabinet,

the latter should be situated at least 700 mm (millimetres)

away from the hob, as shown in the figure.

e) the cut-out for the cooker cabinet should have the

dimensions indicated in the figure.

Min.

Levelling your appliance (only on a few models)

Your cooker is supplied with feet for levelling the appliance. If

necessary, these feet can be screwed into the housings in

the corners of the cooker base (Fig. A).

Mounting the legs (only on a few models)

Press-fit legs are supplied which fit under the base of your

cooker (Fig. B).

Fig. A

Electrical connection

The power supply cable since its size depends on the electric

connection (see the following connection diagram).

Installation

HOOD

600

mm.

Fig. B

400 3N

H05RR-F 5x2.5 CEI-UNEL 35363

400V 2N

H05RR-F 4x2.5 CEI-UNEL 35363

230V 1N

H07RN-F 3x4 CEI-UNEL 35364

Feeding cable installation

Terminal block opening:

· Unscrew screw "V" (Fig. C)

· Pull and open the junction block lid

For the installation of the feeding cable carry out the following

operations:

· position the small connection A-B according to the type

of connection that has to be performed using the scheme

shown in the figure D.

Note: the small connections are prepared by the Factory for

the 230V monophase connection (contacts 1-2-3 are

connected to one another). The bridge 4-5 is situated in the

lower part of the terminal block.

· introduce the cables (N and

and tighten the relative screws.

· fix the remaining cables on the 1-2-3 clips.

· fix the feeding cable in the special cable stop and close

the cover fastening it with the screw "V".

Fig. C

Connecting the supply cable to the mains

Fit a plug, normalised for the load indicated on the data plate,

on the cable; when making the connection directly to the

mains, an omnipoIar switch with a minimum opening of 3

mm between the contacts, must be installed between the

appliance and the mains. This switch must be sufficient for

the load and must comply to regulations in force (the earthing

wire must not be interrupted by the switch). The power supply

cable must be positioned so that it does not exceed 50°C

more than room temperature at any point of its length. Before

making the connection check that:

· the limiter valve and the home system can support the

appliance load (see data plate);

· the power supply system has an efficient earthing

connection which complies with the provisions of current

regulations;

· the socket or omnipoar circuit-breaker is easily accessible

once the cooker has been installed. The plug and socket

must be easily accessible.

S N

) as shown in the figure

Fig. D