Indesit PWDE 8147 S Instrukcja obsługi - Strona 13

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Pralka/suszarka Indesit PWDE 8147 S. Indesit PWDE 8147 S 16 stron.

Drukuj stronę

Troubleshooting

Your washer-dryer could occasionally fail to work. Before contacting the Technical Assistance Service (see " Service"), make

sure that the problem cannot be solved easily using the following list.

Problem:

The machine does not switch on.

The wash cycle does not start.

The machine does not dry.

The clothes are too hot when the

drying cycle is finished.

The machine does not fill with

water or 'H20' flashes on the

display.

The machine continuously fills with

water and continually drains away

or Water left in the drum

or Stuck on wash.

The machine does not drain or spin

(error lights flashing).

The machine does not spin.

The machine does not drain or spin

- 'EASY IRON' & 'START/PAUSE'

indicator lights flash.

The wash programme takes too

long.

The machine vibrates a lot during

the spin cycle.

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or not enough to make contact.

• There is no power to the socket, or the fuse has blown in the mains plug.

• The door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been turned on to allow water to flow into the machine.

• A delayed start has been set.

• Check the 2 sections above.

• The 'DRY' button has been pressed to exclude drying.

• A cooling-down period is always added to the end of each drying cycle. If the

clothes appear too hot to handle leave the door open to allow to cool further

before removing from the machine.

• The water inlet hose is kinked.

• The water inlet hose is not connected to the water supply.

• The water pressure is too low.

• The water tap has not been turned on to allow water to flow into the machine.

• There is no water supply to the house.

• The inlet valve filter is blocked.

• The START/PAUSE button has not been pressed.

• The top of the drain hose is too low - It must be fitted at a height between 65

and 100 cm from the floor (see "Installation").

• The drain hose is connected incorrectly to the sink trap allowing water to run

into the machine, the drain hose must be positioned higher than the bottom of

the sink to prevent water flowing down the drain hose.

• The end of the drain hose has been pushed too far down the standpipe, the

'U' bracket should be fitted 100 mm from the end of the drain hose.

• The Pump filter is blocked.

• The drain hose is kinked (see "Installation").

• New Installation - The blanking cap or spigot has not been removed if

connected under a sink.

• The drain hose or sink trap is blocked.

• The Spin Speed is set to zero.

• If the 'EASY IRON' option is enabled, at the end of the program the machine

drum will rotate slowly. To complete the program press the 'START/PAUSE' or

the 'EASY IRON' buttons.

• If the 'DELICATES' programs are selected, at the end of the program it requires the

drain phase to be started. To complete the program press the 'START/PAUSE' or

the 'EASY IRON' buttons.

• Programme times will vary due to water pressure, the incoming water temperature

and if the wash load goes out of balance. This will increase the programme times

accordingly (see ' The machine wont spin properly' below) - (Most Common Cause!).

• The feet have not been adjusted, enabling the machine to rock.

• New Installation - Either the Transit Bolts including the plastic spacers, or the

Polystyrene Packaging have not been removed when installing the machine.

• The machine is trapped between cabinets and/or walls.

• The load is in a slight out of balance condition and machine is spinning, but at

a lower speed.