Indesit WD 12 S Instrukcja instalacji i użytkowania - Strona 10

Przeglądaj online lub pobierz pdf Instrukcja instalacji i użytkowania dla Pralka/suszarka Indesit WD 12 S. Indesit WD 12 S 21 stron. Indesit washer-dryer instructions for installation and use

Drukuj stronę

Troubleshooting

Before calling, read the following

In most cases, when your washer-dryer fails to work, the problems arising can

be easily solved without having to call for a technician. Before calling for

assistance, always check these points.

The washer-dryer fails to

start.

Is the plug correctly inserted

into the socket? It could have

been moved whilst cleaning.

Is there electricity in the

house?

A circuit breaker may have

switched off as a result of too

many electrical appliances

working at the same time. Or

maybe due to a general failure

in your entire area.

Is the washer-dryer door

closed properly?

For safety reasons, the

washer-dryer cannot work if

RIGHT

Turn off the water

supply after use.

This will eliminate

the possibility of

leakage.

Always leave the

appliance door ajar

to avoid bad odours.

Clean the

appliance's

exteriors gently.

To clean the

exteriors and the

rubber parts of the

appliance, always

use a soft cloth

dipped in warm and

soapy water.

the door is open or not shut

properly.

the

On/Off

button

pressed?

If it is, then a programmed start

has been set.

Is the programmed start

knob, in the correct position

for

those

models

concerned?

Is the water supply turned

on? For safety reasons, if the

washer-dryer does not load

water, it cannot start a wash

cycle.

WRONG

Leave the washer-dryer

plugged in while

cleaning.

Even during maintenance,

the appliance should

always be unplugged.

Use solvents and

aggressive abrasives.

Never use solvents or

abrasives to clean the

external and rubber parts

of the washer-dryer.

Neglect the detergent

dispenser.

It is removable and can

easily be cleaned by

leaving it under running

water.

Go on holiday without

thinking about her.

Before leaving, always

make sure that the

washer-dryer is

unplugged and that the

water supply is turned off.

But where did all the water go?

Simple: with the new Indesit technology, you need less than

half of it, to get good results on twice as much!

This is why you cannot see the water through the door:

because there is little, very little of it, to respect the

environment yet without renouncing maximum cleanliness.

And, on top of that, you are also saving electricity.

The washer-dryer fails to

fill with water.

Is the hose correctly

connected to the tap?

Is there a water shortage ?

There could be work in

progress in your building or

street.

Is there sufficient water

pressure? The autoclave

may be malfunctioning.

Is the tap filter clean? If the

water is very calcareous, or

if work has recently been

carried out on the water

piping, the tap filter could be

clogged with particles and

debris.

Is the rubber hose kinked?

The tract of the rubber hose

bringing water to washer-

dryer must be as straight as

possible. Make sure it is not

squashed or kinked.

The programme selector

knob keeps turning?

Wait a few minutes for the

drain pump to empty the

tub, switch the washer-dryer

off, select one of the symbols

stop/reset

, then switch it

back on. If the knob continues

to turn, call for assistance

because it is showing an

anomaly.

The washer-dryer

continuously fills and

drains water.

Is the drain hose positioned

too low? It must be installed

at a height ranging from 60 to

100 cm.

Is the end of the hose

immersed in water?

Does the wall drainage

system have a breather

pipe? If the problem persists

even after these checks, turn

the water supply off the

machine

and

call

assistance.

If you live on an upper floor of

your building, there may be a

problem with your drain trap.

To solve this problem, a

special valve must be

installed.

for