Indesit XWDE 961680 Instrukcja obsługi - Strona 10

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Pralka/suszarka Indesit XWDE 961680. Indesit XWDE 961680 20 stron.

Drukuj stronę

How to run a wash cycle or a

drying cycle

Rapid programming

1. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes and wash cycles on the following page.

2. ADD THE DETERGENT. Pull out the detergent

dispenser drawer and pour the detergent into the relevant

compartments as described in "Detergents and laundry".

3. CLOSE THE DOOR.

4. Press the "PUSH&WASH+DRY" button to start the

programme.

Traditional programming

1. SWITCH THE MACHINE ON. Press the

the START/PAUSE indicator light will flash slowly in a

green colour.

2. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes and wash cycles on the following page.

3. ADD THE DETERGENT. Pull out the detergent

dispenser drawer and pour the detergent into the relevant

compartments as described in "Detergents and laundry".

4. CLOSE THE DOOR.

5. SELECT THE WASH CYCLE. Use the WASH CYCLE

SELECTOR knob to select the desired wash cycle. A

temperature and spin speed is set for each wash cycle;

these values may be adjusted. The duration of the cycle

will appear on the display.

6. CUSTOMISE THE WASH CYCLE. Use the relevant buttons:

Modify the temperature and/or spin

speed. The machine automatically displays the

maximum temperature and spin speed values set for

the selected cycle, or the most recently-used settings

if they are compatible with the selected cycle. The

temperature can be decreased by pressing the

button, until the cold wash "OFF" setting is reached.

The spin speed may be progressively reduced by

pressing the

(the "OFF" setting). If these buttons are pressed again,

the maximum values are restored.

Setting the drying

The first time the button

automatically select the maximum drying cycle which is

compatible with the selected wash cycle. Subsequent

presses will decrease the drying level and then the drying

time, until the cycle is excluded completely ("OFF").

Drying may be set as follows:

A- Based on the desired laundry dryness level:

Cupboard

suitable for laundry which can be put

back in a cupboard without being ironed.

Hanger

ideal for clothes which do not need to be

dried fully.

suitable for clothes which will need ironing

Iron

afterwards. the remaining dampness softens creases,

making them easier to remove.

B - Based on a set time period: between 210 and 30 minutes

button, until it is completely excluded

cyclea

is pressed, the machine will

If your laundry load to be washed and dried is much

greater than the maximum stated load (see adjacent

table of wash cycles), perform the wash cycle, and

when the cycle is complete, divide the garments into

groups and put some of them back in the drum. At this

point, follow the instructions provided for a "Drying

only" cycle. Repeat this procedure for the remainder of

the load.

a cooling-down period is always added to the end

Note:

of each drying cycle.

Drying only

Press button

After selecting the desired cycle (compatible with

the type of garments), press button

button;

the washing phase and start the drying phase at the

maximum level for the selected cycle. The drying level

or time may be set and changed by pressing the drying

button

(Not compatible with cycles 13 and 14).

Setting a delayed start.

To set a delayed start for the selected cycle, press the

corresponding button repeatedly until the required delay

period has been reached. When this option has been

activated, the

remove the delayed start setting, press the button until

the text "OFF" appears on the display.

Modify the cycle settings.

• Press the button to enable the option; the indicator

light corresponding to the button will switch on.

• Press the button again to disable the option; the

indicator light will switch off.

! If the selected option is not compatible with the set

wash cycle, the indicator light will flash and the option

will not be activated.

! The options may affect the recommended load value

and/or the duration of the cycle.

7. START THE WASH CYCLE. Press the START/

PAUSE button. The corresponding indicator light will

turn green, remaining lit in a fixed manner, and the door

will be locked (the DOOR LOCKED

To change a wash cycle while it is in progress, pause

the washer-dryer using the START/PAUSE button

(the START/PAUSE indicator light will flash slowly in an

amber colour); then select the desired cycle and press

the START/PAUSE button again. To open the door

while a cycle is in progress, press the START/PAUSE

button; if the DOOR LOCKED

off the door may be opened. Press the START/PAUSE

button again to restart the wash cycle from the point at

which it was interrupted.

8. THE END OF THE WASH CYCLE. This will be

indicated by the text "END" on the display; when the

DOOR LOCKED

be opened. Open the door, unload the laundry and

switch off the machine.

! If you wish to cancel a cycle which has already begun,

press and hold the

and the machine will switch off.

to perform the drying-only cycle.

symbol lights up on the display. To

symbol is switched

symbol switches off the door may

button. The cycle will be stopped

to exclude

symbol will be lit).