Indesit PAA 642 IX/I Instrukcja obsługi - Strona 5

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Hob Indesit PAA 642 IX/I. Indesit PAA 642 IX/I 16 stron.

Drukuj stronę

Installation

! Before operating your new appliance please read this instruction booklet

carefully. It contains important information for safe use, installation and care

of the appliance.

! Please keep these operating instructions for future reference. Pass them on

to possible new owners of the appliance.

Positioning

! Keep packaging material out of the reach of children. It can become a choking

or suffocation hazard (see Precautions and tips).

! The appliance must be installed by a qualified professional according to the

instructions provided. Incorrect installation may cause harm to people and

animals or may damage property.

! This unit may be installed and used only in permanently ventilated rooms

in accordance with current national regulations. The following requirements

must be observed:

• The room must be equipped with an air extraction system that expels

any combustion fumes. This may consist of a hood or an electric fan that

automatically starts each time the appliance is switched on.

In a chimney stack or branched flue.

(exclusively for cooking appliances)

• The room must also allow proper air circulation, as air is needed for

combustion to occur normally. The flow of air must not be less than 2 m

per kW of installed power.

The air circulation system may take air directly

from the outside by means of a pipe with an

inner cross section of at least 100 cm

opening must not be vulnerable to any type

of blockages.

Examples of

ventilation holes

for comburant air.

The system can also provide the air needed for

Adjacent

Room to be

Room

Vented

combustion indirectly, i.e. from adjacent rooms

fitted with air circulation tubes as described

above. However, these rooms must not be

communal rooms, bedrooms or rooms that

may present a fire hazard.

Enlarging the ventilation slot

between window and floor.

• Intensive and prolonged use of the appliance may necessitate

supplemental ventilation, e.g. opening a window or increasing the power

of the air intake system (if present).

• Liquid petroleum gas sinks to the floor as it is heavier than air. Therefore,

rooms containing LPG cylinders must also be equipped with vents to allow

gas to escape in the event of a leak. As a result LPG cylinders, whether

partially or completely full, must not be installed or stored in rooms or

storage areas that are below ground level (cellars, etc.). It is advisable to

keep only the cylinder being used in the room, positioned so that it is not

subject to heat produced by external sources (ovens, fireplaces, stoves,

etc. ) which could raise the temperature of the cylinder above 50°C.

Fitting the appliance

The following precautions must be taken when installing the hob:

• Kitchen cabinets adjacent to the appliance and taller than the top of the

hob must be at least 200 mm from the edge of the hob.

• Hoods must be installed according to their relative installation instruction

manuals and at a minimum distance of 650 mm from the hob (see figure).

• Place the wall cabinets adjacent to the hood at a minimum height of 420

mm from the hob (see figure).

• The installation cavity should have the dimensions indicated in the figure.

NOTE: In case of installation of a hood above the hob, please refer to the

hood instructions for the correct distance.

• After having cleaned the perimeter surface, apply the supplied gasket to

the hob as shown in the figure.

Directly to

the Outside

; the

Position the hob in the worktop opening made respecting the dimensions

indicated in the Instruction.

NOTE: the power supply cable must be long enough to permit its upward

extraction.

To secure the hob, use the brackets (A) provided with it. Fit the brackets into the

relevant bores shown by the arrow and fasten them by means of their screws

in accordance with the thickness of the worktop (see the following figures).

• Where the hob is not installed over a built-in oven, a wooden panel must

be installed as insulation. This must be placed at a minimum distance of

20 mm from the lower part of the hob.

If the hob is installed beneath a wall cabinet,

the latter must be situated at a minimum of 700

mm above the hob.

600mm min.

Top 20 mm

Top 30-50 mm