Indesit IDPE G45 A1 ECO Instrukcja obsługi - Strona 13
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Suszarka Indesit IDPE G45 A1 ECO. Indesit IDPE G45 A1 ECO 16 stron. Tumble dryer
Drukuj stronę
Options
EN
The options allow for customising the selected programme according to one's own needs.
Timed drying
After selecting a programme, press the "Timed drying" button to enter a drying time. Every time this button is pressed, the duration of
the selected drying cycle appears on the display. When pressed the first time, the highest allowed value for the selected cycle appears
on the display. When pressed each of the following times, the set time is reduced until OFF appears.
The buzzer will activate if the timed drying option is not available.
Delay Start
The start of some programmes (see Programmes and options) may be delayed up to 24 hours. Before selecting a programme with
a delayed start make sure that the water bottle is empty and the filter is clean. The drum will rotate occasionally before the drying
programme starts to prevent the formation of creases.
High Heat
When a drying time is selected, pressing this button sets a high heat drying and the indicator light above the button lights up. The
timed programmes are pre-set to low heat.
Fast Iron
This option, when selected, delivers for the cycle chosen the best humidity level to help make ironing quicker and easier. This option
stops the cycle at the ideal dryness level for ironing thus making ironing easier and faster. (See programme guide and options).
Memo
This option allows you to store your cycle selection along with any associated options and to easily use a previously stored cycle.
Delayed start options cannot be stored.
•Press and hold the button MEMO for 3 second to store a cycle. You can press this button when the desired cycle and associa-
ted options have been selected either before the cycle has started or during the drying cycle. When you press and hold the Memo
button the LED flashes as well as the time on the display and after 3 second a beep will confirm that the details have been stored.
•To recall the stored cycle simply turn on the dryer, press the memo button and then start the cycle. It is possible to change any of
the options in the normal way. Every 2 minutes the stored cycle number will appear on the display. If no cycle has been stored you
will hear a beep when the Memo button is pressed.
•A stored programme can be overwritten with a new programme just by repeating the steps outlined above.
Alarm
A buzzer sounds at the end of the drying cycle to signal that the programme has ended and the garments are ready to be removed.
Not all options are available on all programmes (see Programmes and options).
Opening the door
If the door is opened (or the START/PAUSE button is pressed) while a programme is running, the dryer stops and the following may
occur:
• The START/PAUSE button flashes orange.
• When a delayed start is running, the delay countdown continues. It is necessary to press the START/PAUSE button to resume
the "Delay start" programme. The "Delay start" indicator light flashes and the display visualises the time remaining to the start of the
selected programme.
• It is necessary to press the START/PAUSE button to resume the programme. The progress indicator lights signal the running pha-
se and the START/PAUSE indicator light stops flashing and turns green.
• During the post anti-crease phase, the programme ends. Pressing the START/PAUSE button reactivates a new programme from
the
beginning.
• By turning the Programme selection knob, a new programme is selected and the START/PAUSE indicator light flashes green. This
procedure can be used to select the COOL drying programme to cool garments if they are judged to be dry enough.
Press the START/PAUSE button to start the new programme.
Heat Pump Protection System
The heat pump sytem has a compressor protection feature, that operates if you open the door or there is a power disruption or you
turn off the dryer. This system will prevent the heat pump compressor from starting for 5 minutes after the door is closed and the
programme started.
Note: If you have a power cut, switch off the power or remove the plug. When power is restored, plug in the machine, press and
hold the ON/OFF button until the dryer reactivates, then press Start/Pause button.
13
13