AEG A 85230 GT Podręcznik użytkownika - Strona 4
Przeglądaj online lub pobierz pdf Podręcznik użytkownika dla Zamrażarka AEG A 85230 GT. AEG A 85230 GT 8 stron. Electrolux freezer user manual
Również dla AEG A 85230 GT: Podręcznik użytkownika (32 strony)
Drukuj stronę
Danger!
Ensure that the freezer is not resting on the power
supply cable.
Do not remove the power supply cable by pulling on its
lead, particularly when the freezer is being pulled out of
its niche.
The power supply cable may only be replaced by a
qualified electrician.
Ensure that the power plug is not squashed or
damaged by the back of the freezer.
There must be adequate ventilation around the
appliance.
Any electrical work required to install this appliance
should be carried out by a competent electrician.
Electrical connection
The appliance is supplied with a 13amp plug fitted. In the
event of having to change the fuse in the plug supplied, a
13amp ASTA approved (BS1362) fuse must be used.
Should the plug need to be replaced for any reason. The
wires in the power supply cable are coloured in
accordance with the following code:
Green and Yellow - Earth: must be connected to the
terminal marked with the letter "E" or by the earth
symbol or coloured green and yellow.
Blue - Neutral: must be connected to the terminal "N"
or coloured black.
Brown - Live: must be connected to the terminal
marked "L" or coloured red.
Upon completion there must be no cut, or stray strands of
wire present and the cord clamp must be secure over the
outer sheath.
Warning! This appliance must be earthed.
First use
Before first use, the freezer should be cleaned inside,
see chapter "Care and cleaning".
Plug in the appliance.
Press button (A) to switch the appliance on.
The display will illuminate.
The symbol (
) will flash on the display and the alarm
will beep, to indicate that the temperature inside the
freezer is not yet cold enough for food storage.
Press button (E) to switch the alarm off. The symbol
(
) will normally stop flashing after several hours.
Only place food inside the freezer once the symbol
(
) has gone. The temperature of the freezer is set to
4
reach -18°C, which is the optimal storage temperature
as set in the Eco Mode (
Switch on-off
Switch on the freezer
Press button (A) to switch the appliance on.
The display comes on.
Switch off the freezer
Press button (A) for more than one second until the
countdown "3-2-1" disappears and you hear a
sequence of beeps.
The display goes off.
Warning! Do not place objects on the control panel, as
they might accidentally switch off the freezer.
Daily use
Temperature adjustment
The temperature may be adjusted between -15°C and -
24°C. We suggest setting the freezer temperature to -
18°C, which guarantees proper freezing and conservation
of frozen food.
Press button (B) several times until the desired
temperature is reached.
The temperature on the display flashes and indicates
the temperature set.
Press button (E) to confirm the desired temperature.
You will hear a beep.
The temperature on the display stops flashing again
and indicates the temperature inside the freezer.
The newly adjusted temperature is reached after
several hours. During this time it is normal that the
temperature displayed is different from the temperature
set.
Attention! Differences between the temperature displayed
and the temperature set are normal, especially when:
The temperature setting has recently been adjusted.
The lid has been left open for a long time.
Warm food has been placed in the freezer.
The Super Freeze function is activated.
Super Freeze function
If more than 3-4 kg of fresh food is to be frozen, the freezer
needs to be pre-cooled.
At least 24 hours before placing fresh food in the
freezer, press button (D) several times until the
corresponding symbol (
Press button (E) within a few seconds to confirm the
Super Freeze activation. The symbol (
flashing, you will hear a beep and the animation on the
display speeds up.
Place the food in the freezer. After 52 hours this
function will automatically stop and the freezer will
return to normal storage temperature. This function
can be de-activated at any time by pressing button (D)
until the corresponding symbol (
display again and then by pressing button (E) to
confirm the de-activation.
)
) flashes on the display.
) stops
) flashes on the