Kohler 10EKD Instrukcje instalacji - Strona 2

Przeglądaj online lub pobierz pdf Instrukcje instalacji dla Produkt hydrauliczny Kohler 10EKD. Kohler 10EKD 4 stron.
Również dla Kohler 10EKD: Instrukcja instalacji (17 strony)

Drukuj stronę

Remove the sound shield.

2.1

Remove the sound shield's exhaust panel,

generator-end door, and roof (if necessary) to gain

access to the generator set hoses inside. See

Figure 2.

1. Exhaust panel

2. Generator-end door

3. Roof

Figure 2 Sound Shield Removal

Install the siphon break.

3.1

Remove the 2 button plugs from the exhaust panel

on the sound shield.

3.2

Install the 2 grommets (X-284-7) and 2 hose

connectors (344934) to the openings in the

exhaust panel. See Figure 7.

3.3

Find and remove the molded hose located

between the seawater flow switch and the exhaust

catalyst. Save the hose clamps.

1. Remove molded hose (GM55092) and save hose clamps

(X-426-12 qty. 2).

2. Seawater flow switch

Figure 3 Hose Removal

3.4

Secure the hose (X-312-16) to the seawater flow

switch using the hose clamp saved in step 3.3.

See Figure 6.

Note: 5/7.5EKD and 4/6EFKD Models: Cut the hose

(X-312-16) to fit.

OUT

GM58158-M

3.5

Route the hose from the seawater flow switch to

the left hole in the sound shield's exhaust panel.

Secure the hose with the other hose clamp.

3.6

Rotate the fitting on the exhaust catalyst and

secure the hose (X-312-61) to the exhaust catalyst

using a hose clamp (X-426-12). See Figure 6.

Note: 5/7.5EKD and 4/6EFKD Models: Cut the hose

(X-312-61) to fit.

3.7

Route the hose from the exhaust catalyst to the

remaining hole in the sound shield's exhaust

panel.

(X-426-12).

Note: Because of the variety of possible installations,

this kit does not include hoses to connect to the

siphon break. See Figure 4 for an ID-size hose

selection. Use coolant hoses (SAE 20R1, class B

or equivalent) and hoses suitable for marine use.

Use corrosion-resistant or stainless steel hose

clamps on all fittings.

Kit Number

GM60007-KP1

Figure 4 Hose Selection

3.8

Determine the required length of hose from each

hose connector to the siphon break. Cut two

pieces of the customer-supplied hose to the

determined length. See Figure 7.

Note: The siphon break must be at least 30 cm (12 in.)

above the waterline during maximum load and

generator shutdown condition.

3.9

Use the customer-supplied hose clamps to

connect the hoses to the hose connectors. Locate

the hose clamps 12.7 mm (1/2 in.) from each end

of the hose and tighten the clamps. See Figure 7.

3.10 Use customer-supplied hose clamps to connect

the siphon break (GM32985) to the hoses. Locate

the hose clamps 12.7 mm (1/2 in.) from each end

of the hose and tighten the clamps.

3.11 Mount the siphon break to the engine stringer or

other rigid structure. Keep the siphon break reed

valve in a vertical position.

Note: Correct functioning of the reed valve requires

clean operating conditions. Locate the top of the

siphon break (reed valve) away from possible

accumulated dirt and other contaminants.

Note: To prevent water leakage on the generator set, do

not mount the siphon break over the generator

set.

Secure the hose with a hose clamp

ID-Size Hose

mm (in.)

15.9 (5/8)

TT-1509

4/14