Kohler 30RES Podręcznik - Strona 7

Przeglądaj online lub pobierz pdf Podręcznik dla Przenośny generator Kohler 30RES. Kohler 30RES 36 stron. Residential generator sets

Drukuj stronę

Propane (LP)—Adequate ventilation

is mandatory.

Because propane is

heavier than air, install propane gas

detectors low in a room. Inspect the

detectors

per

the

manufacturer's

instructions.

Natural Gas—Adequate ventilation is

mandatory. Because natural gas rises,

install natural gas detectors high in a

room. Inspect the detectors per the

manufacturer's instructions.

Gas fuel leaks.

Explosive fuel

vapors can cause severe injury or

death. Fuel leakage can cause an

explosion. Check the LP vapor gas or

natural gas fuel system for leakage by

using a soap and water solution with

the fuel system test pressurized to

6--8 ounces

per

square

(10--14 inches water column). Do not

use a soap solution containing either

ammonia or chlorine because both

prevent bubble formation. A successful

test depends on the ability of the

solution to bubble.

Hazardous Noise

CAUTION

Hazardous noise.

Can cause hearing loss.

Never operate the generator set

without a muffler or with a faulty

exhaust system.

Engine noise. Hazardous noise can

cause hearing loss. Generator sets

not equipped with sound enclosures

can produce noise levels greater than

105 dBA. Prolonged exposure to noise

levels greater than 85 dBA can cause

permanent hearing loss. Wear hearing

protection when near an operating

generator set.

TP-6344 4/09

Hazardous Voltage/

Moving Parts

DANGER

Hazardous voltage.

Will cause severe injury or death.

Disconnect all power sources before

opening the enclosure.

WARNING

inch

Hazardous voltage.

Can cause severe injury or death.

Operate the generator set only when

all guards and electrical enclosures

are in place.

WARNING

Hazardous voltage.

Backfeed to the utility system can

cause property damage, severe

injury, or death.

If the generator set is used for

standby power, install an automatic

transfer switch to prevent inadvertent

interconnection

normal sources of supply.

CAUTION

Welding the generator set.

Can

cause

equipment damage.

Never weld components of the

generator

set

disconnecting the battery, controller

wiring harness, and engine electronic

control module (ECM).

Moving parts.

standby

and

severe

electrical

without

first

Grounding electrical equipment.

Hazardous

voltage

can

severe injury or death. Electrocution

is possible whenever electricity is

present. Ensure you comply with all

applicable

codes

and

Electrically ground the generator set,

transfer switch, and related equipment

and electrical circuits. Turn off the main

circuit breakers of all power sources

before servicing the equipment. Never

contact electrical leads or appliances

when standing in water or on wet

ground because these conditions

increase the risk of electrocution.

Disconnecting the electrical load.

Hazardous

voltage

can

severe injury or death. Disconnect

the generator set from the load by

turning off the line circuit breaker or by

disconnecting the generator set output

leads from the transfer switch and

heavily taping the ends of the leads.

High voltage transferred to the load

during testing may cause personal

injury and equipment damage. Do not

use the safeguard circuit breaker in

place of the line circuit breaker. The

safeguard circuit breaker does not

disconnect the generator set from the

load.

Welding on the generator set. Can

cause severe electrical equipment

damage.

Before welding on the

generator set perform the following

steps: (1) Remove the battery cables,

negative (--) lead first. (2) Disconnect

all engine electronic control module

(ECM) connectors. (3) Disconnect all

generator set controller and voltage

regulator circuit board connectors.

(4) Disconnect the engine battery-

charging

alternator

connections.

(5) Attach the weld ground connection

close to the weld location.

Installing

the

battery

Hazardous

voltage

can

severe

injury

death.

ungrounded battery

charger may

cause electrical shock. Connect the

battery charger enclosure to the ground

of a permanent wiring system. As an

alternative,

install

grounding

conductor

with

conductors and connect it to the

equipment grounding terminal or the

lead on the battery charger. Install the

battery charger as prescribed in the

equipment manual. Install the battery

charger in compliance with local codes

and ordinances.

Safety Precautions and Instructions

cause

standards.

cause

charger.

cause

equipment

circuit