Aqua Cooler AC-PN8EBFY Instrukcja obsługi i konserwacji - Strona 7

Przeglądaj online lub pobierz pdf Instrukcja obsługi i konserwacji dla System wodny Aqua Cooler AC-PN8EBFY. Aqua Cooler AC-PN8EBFY 12 stron. Surface mounted bottle filler

Drukuj stronę

INSTALLATION CONT.

Complete the installation by turning on the water source and checking for leaks.

Ensure nothing is obstructing the fan blade. Plug the power cord back into the wall outlet and

then test to ensure the bottle filler is functioning properly.

Once the unit has been verified to be functioning properly, install the front cover panel by

inserting the top flanch up between the wrapper and center bracket, then tipping the panel back

to the fountain. Secure it with the 2x #8 hex screws at the base of the unit.

Complete the installation by installing the Bottle Filler top and filter Access Panels.

Your Partner in Cool.

SET-UP GUIDES

BOTTLE FILLER ELECTRONICS:

Factory default program settings:

• Units: Gallons

• Unfiltered unit

• Flow meter = Rate selected

• Filter capacity = 1250 gallons (4731L)

• Bottle count = 0.5L (1 bottle)

• Flow rate = 1.2 GPM

• 20s max dispense time.

For each model top cap will need to be set aside until programming is complete. Remove top

cap by unscrewing two (2) T15 torx screws if needed. Remove wire tie bundling pushbutton

inside bottle filler and feed it through hole in cooler top. You can then adjust program using

pushbutton through access panel of cooler.

To change the program settings, follow these steps:

DISPLAY

ACTION

000000000 BOTTLES

Depress button for 3 seconds to enter into the following menu settings and make changes.

REUSED

Note: at anytime it will exit menu and save settings when idle for 10 seconds (no button press) and

(Home Screen)

revert back to Home Screen.

LTR/GAL

Depress button for 3 seconds to change from Gallons to Litres, or momentary press to advance to

GAL

next menu.

UNFILT/FILT?

Depress button for 3 seconds to change from Unfiltered to Filtered unit, or momentary press to

UNFILT UNIT

advance to next menu

FLOW METER?

Depress button for 3 seconds to change from Rate Selected to (Flow) Meter Enabled, or

RATE SELECTED

momentary press to advance to next menu

SELECT RATE

To change flow rate, momentarily depress button to change whole gallon digit.

1.2 GPM UNIT

Hold button 3 seconds to advance to TENTHS of gallon digit.

Depress momentarily to change the digit.

Hold button 3 seconds to advance to the next menu.

RESET 000000000

Depress button for 3 seconds to reset Gallon or Litre count, or momentary press to advance to

GALLON CNT

next menu

[LTR COUNT]

FILT CAPAC

Depress button for 3 seconds to change filter capacity to 3000 GAL [11355 Litres] for Versafiller I

OF 1250 GAL

or Galaxi green filter, or momentary press to advance to next menu

[4731 LTR]

3 sec rule?

Depress button for 3 seconds to switch from 0.5L bottle to 3 sec rule, or momentary press to

0.5L

advance to next menu. (The 3 Sec rule increases the bottle count based on a 3 second dispense.)

RESET 00000000

Depress button for 3 seconds to reset (Home Screen) BOTTLES REUSED count, or momentary

BOT COUNT?

press to advance to next menu.

Bot Filler

Depress button for 3 seconds to change maximum dispense time to 10, 20, or 30 seconds, or

Set_time:20s

momentary press advance to next menu.

RUN CAL

Depress button for 3 seconds to run calibration again, or momentary press to advance to next

AGAIN?

menu.

REMOVING FROM SERVICE

• Close water shut off valve and disconnect power to the CHILLER.

• Provide container to catch water to be drained and place under the cold tank drain.

• Remove the drain plug from the drain tube.

• Actuate the bottle filler and allow the water to drain into the bucket. Replace drain plug.

• Disconnect power to the BOTTLE FILLER.

• Disconnect the water supply line at the shut off valve.