DF-models I-Peak 30 Skrócona instrukcja obsługi - Strona 2

Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla Ładowarka DF-models I-Peak 30. DF-models I-Peak 30 4 stron. V3

DF-models I-Peak 30 Skrócona instrukcja obsługi
INTRODUCTION
Thank you for your choice of the I-Peak 30, 100-240V AC balance charger. This unit is
simple to use but its operation does require some knowledge on the part of the user. Please read this
entire operating manual completely and attentively before using this product, as it covers a wide range
of information on operating and safety.
I-Peak 30 is an economic, high quality 100-240V AC balance charger, designed for charging
LiPo/LiFe/LiHv batteries from 2-4 cells and NiMH/NiCd batteries from 4-8 cells. The circuit power is 30W
and max charge current can reach to 3A. There are three different charge current 1A/2A/3A which can
be selected. You could select the proper charge current according to battery capacity.
Status LED Indicator:
Green LED:Full charged or ready to charge
Red LED: Under charging or charge protected
Battery Type Switch Button
Battery Socket
CHARGE PROCEDURES
I-Peak 30 comes with the built in power supply. You can connect the AC power cord
to the AC socket (100-240V AC) directly.
For charging Lipo/LiFe/LiHV battery type
Please refer to following steps to charge the battery,
Insert the AC power cord into the charger.
1)
Insert the AC cord into a wall socket (100-240V). All 5 LEDS will light for 1-2 seconds and switch to
2)
first LED light on, then charge status LED will flash green which indicates the charger is ready to
charge.
3)
Push mode button to select the proper charging battery type
4)
Select the proper charging current 1A/2A/3A by the toggle switch.
5)
Connect the battery to the charger main battery lead to battery socket and balance wires to balance
socket. Then charger starts charging.
6)
During the charging progress, when the charge status LED glows constant red, the charger is
charging in CC mode; when the charge status LED glows constant orange, the charger is charging in
CV mode;
7)
When the battery is fully charged, the charge status LED will glow constant green.
8)
Unplug the battery from the charger and the charge status LED will flash green which indicates the
charger is ready to charge another battery.
AC 100-240V
Power Jack
Battery Type:
LiPo/LiFe/LiHv,
NIMH/NICD
XH Balance Socket
Charge Current Switch
- -
1
For charging NiMH/NiCd battery type
Please refer to following steps to charge the battery.
1)
Insert the AC power cord into the charger.
2)
Insert the AC cord into a wall socket (100-240V). All 5 LEDS will light for 1-2 seconds and switch to
first LED indicator, then charge status LED will flash green which indicates the charger is ready to
charge.
3)
Push mode button to switch NiMh/MiCd LED indicator.
4)
Select the proper charging current 1A/2A/3A by the toggle switch.
5)
Connect main battery lead to battery socket only, push mode button 2-3seconds, Status LED will
change from green blinking to red constantly, then charger starts charging.
6)
When the battery is fully charged, the charge status LED will glow constant green.
7)
Unplug the battery from the charger and the charge status LED will flash green which indicates the
charger is ready to charge another battery.
CAUTION:
Please use the correct way to connect your battery to
I-Peak 30
the
charger while charging in balance
mode. Failure to connect will damage this charger.
For LiPo/LiFe/LiHv battery charging, the main battery
leads must be connected along with the balance lead
connector as shown before charging your battery!
Protection Status
5 red LED blink in one time and then Pause for a second
Connection break
Balance connect error
5 red LED blink in three times and then Pause for a second
5 red LED blink in four times and then Pause for a second
Temperature protection
5 red LED blink in five times and then Pause for a second
Reverse polarity/Over Charge
SPECIFICATION
AC Input Voltage
Output Power
Charge Current
LiPo/LiFe/LiHv cell count
NiMH/NiCd battery cell count
Dimension
Weight
100-240V AC
30W
1A/2A/3A
2-4 cells
4-8 cells
110x68x35mm
220g
DF Models
Jürgen Kamm
www.df-models.com
Drahthammerstr. 22
D-92224 Amberg
WEEE-Reg.Nr.: DE 30915550
This model is no toy.
- -
2