Billi Quadra 440 Instrukcja instalacji - Strona 6
Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Armatura kuchenna i łazienkowa Billi Quadra 440. Billi Quadra 440 8 stron. Tower dispenser
Również dla Billi Quadra 440: Instrukcja instalacji (12 strony)
Drukuj stronę
Installing Quadra Plus mixer tap.
XL, XT, XR.
Additional Components for Billi Quadra
Plus 5, Plus 9 and Plus 15 Models
Before commencing installation, identify
the following components:
1. O-ring (large)
2. Tap base ring
3. Mount clamp plate
4. Mount clamp plate gasket
5. Mount stud
6. Extended fixing nut
7. Barb adaptor fitting (short)
8. Barb adaptor fitting (extended)
9. Spring hose clamps x 2
10. ½" joining nipple
11. 1 metre PVC tubing
12. Braided flexible couplings x 3
13. Mixer Tap
Mixer Tap Mounting Procedure
1. Drill or punch mount hole and deburr.
–Hole size: 35 – 38mm.
–Sink or Benchtop thickness: 1 – 48mm.
2. Feed braided flexible couplings marked
'Water In' and 'Water Out' through mount
hole leaving M10 threaded connection
ends protruding upwards through hole.
Fit O-ring (large) and tap base ring over
tubes and sit them in place.
3. Fit barb adaptor fitting (extended) and
mount stud to mixer tap body.
4. Push PVC tubing onto barb and fit spring
hose clamp. Position hose clamp lugs as
shown in Diagram 20.
5. Feed PVC tube down through mount hole
alongside braided tubes.
6. Fit M10 threaded tubes into tap body.
Match tube labels with tap base
markings.
7. Feed tubing through the mount hole and
place tap in correct position. Mount stud
faces to front of mixer tap. Move lever
from left to right to find lever centre
position.
8. Fit mount clamp gasket and plate to
mounting stud. Note orientation of gasket
and plate – see Diagram 21.
9. Ensure tap is positioned evenly over
the mount hole and that lever position
is correct. Fit and tighten extended nut
using a 12mm tube spanner or large flat
blade screwdriver.
Connecting Mixer Tap to Quadra Plus
Fit tubing connections as shown in Diagram 22.
1. Water supply inlet tube incorporates an
inline strainer. Connect to ½" BSP stop
tap.
2. Fit short barb adaptor to port at the rear
of Quadra unit marked 'Hot Outlet'. Trim
PVC tubing to correct length using sharp
knife. Excess tubing will cause sagging
and possible kinking. Push tube onto
barb adaptor and fit spring hose clamp.
Support may be needed for PVC tube if
there is a horizontal run.
6
3. Fit braided coupling marked 'Hot Inlet' to
matching port. Join to braided coupling
marked 'Water Out' using ½" joining
nipple.
Operating the Mixer Tap
Operation of the mixer tap is as with any
single lever tap. Lift lever to start water flow.
Swing to the left for hot water and to the right
for cold water.
Hot water will not be available until Quadra
boiling water tank has filled and heated.
Bubbling in the hot water flow indicates
insufficient boiling water is available.
Wait a few minutes for tank to fill and heat.
Top View
Quadra Plus
Power
Dispenser
supply
Power
Cord
Vent
Boiling
Chilled
grey tube
red tube
blue tube
Extended
barb
adapter
with PVC
tube fitted.
Note correct
position
of spring
clamp.
Mount
stud
Extended
nut
short barb
adaptor
Hot
Hot
Outlet
Inlet
Condenser
Water
black
supply
tube
Diagram 22b
IN
OUT
H
Diagram 20
35-38mm
hole
IN
OUT
H
mount
clamp plate
Diagram 21
hot tap outlet
PVC tube
water out
hot inlet
15mm
stop tap
Diagram 22a
water
in