Dell DX6012S Instrukcja konfiguracji i ustawień - Strona 17

Przeglądaj online lub pobierz pdf Instrukcja konfiguracji i ustawień dla Przechowywanie Dell DX6012S. Dell DX6012S 43 stron. Rack installation instructions — static rails
Również dla Dell DX6012S: Podręcznik uzupełniający (4 strony), Instrukcja instalacji sprzętu (2 strony), Podręcznik użytkownika (46 strony), Instrukcja instalacji i konfiguracji (35 strony), Podręcznik dla początkujących (28 strony), Zawiadomienie (28 strony), Zawiadomienie (20 strony), Przegląd (19 strony), Podręcznik konfiguracji (9 strony), Podręcznik konfiguracji (9 strony), Uwaga dotycząca wydania (8 strony), Podręcznik konfiguracji (7 strony), Uwaga dotycząca wydania (6 strony), Uwaga dotycząca wydania (5 strony), Informacje o wersji (5 strony), Podręcznik dla początkujących (47 strony), Instalacja (2 strony), Instalacja stojaka (2 strony)

VLAN=yes

4. Start the new interface:

ifup ifcfg-eth1:1

Note, that if the DX Content Router services are installed on a Cluster Services Node (CSN),

creation of the IP addresses is performed automatically when the services are configured.

4.2. Installing and Configuring DX Content Router Services

The DX Content Router distribution is available as a RHEL rpm package that is installed with a shell

script. The package and its dependencies must be installed as a 'root' user with the following steps:

1. Copy the distributed zip file to your RHEL server and unzip it. Unzipping the distribution on a

separate server and then transferring it to the DX Content Router server is not recommended

as the file may become corrupted during the transfer. The following commands will unzip the file

after it has been copied to the server:

$ sudo su -

# unzip contentrouter-install-2.2.0b1.zip -d

2. Install DX Content Router by running the shell script from the directory location where the shell

script was unzipped. For instance, to install the 2.2 Beta 1 version of the software from the

contentrouter-install-2.2.0b1 directory created above you would run the following commands:

$ sudo su -

# cd contentrouter-install-2.2.0b1

# ./contentrouter-install.sh

Note

If the installation fails due to 'Missing Dependency', make sure you have installed the

packages mentioned above in the 3rd Party Package Pre-requisites section.

If DX Content Router is installed on a Cluster Services Node (CSN), the necessary software will be

installed automatically as part of the overall software bundle.

After installing DX Content Router, you must configure the installed services by updating the

configuration files for each service, Replicator and Publisher, you plan to run as well as creating a

filter rules file for Publisher. The configuration files do not exist on the system after installation and

must be created prior to attempting either service. Failure to create and configure these files will

result in a 'Publisher/Replicator not configured' error when you attempt to start the service.

Both services would be utilized for a mirrored configuration where the server is both publishing

UUIDs from a local cluster and receiving incoming UUIDs to replicate from a remote cluster. For a

one-way Disaster Recovery scenario, you would likely only need to configure one of the services

on a single server. Both the Publisher and Replicator services can be configured from the CSN

management console. Please see the 'Configuration' appendix for a full list of all parameters and

best practice instructions for creating the configuration files and rules.xml file by copying the existing

sample configuration.

contentrouter-install-2.2.0b1

Version 2.2

December 2010