Dell S4048-ON Instrukcja rozwiązywania problemów - Strona 9

Przeglądaj online lub pobierz pdf Instrukcja rozwiązywania problemów dla Przełącznik Dell S4048-ON. Dell S4048-ON 29 stron. Enterprise switches
Również dla Dell S4048-ON: Podręcznik konfiguracji (19 strony), Podręcznik konfiguracji (30 strony)

Drukuj stronę

Dell S4048-ON Instrukcja rozwiązywania problemów

ONIE Rescue bypasses the installed operating system and boots the system into ONIE until you reboot the system.

Press ENTER to activate the console.

Example of the Optional ONIE-uninstaller Command

After ONIE Rescue completes, the system resets and boots to the ONIE console.

NOTE:

Only use the optional onie-uninstaller command if you want to remove all the network operating software on your

system except for ONIE. This command removes any installed network operating system.

ONIE:/ # onie-uninstaller

Erasing unused NOR flash region

Erasing 128 Kibyte @ 20000 - 100% complete.

Erasing internal mass storage device: /dev/mmcblk0 (7832MB)

Percent complete: 100%

S4810–ON or S6000–ON diagnostic package

To download the diagnostic package on an S4810–ON or S6000–ON platform, follow these steps.

NOTE:

Before you begin, go to http://www.dell.com/support and download the diagnostic package. You will need your Dell EMC

support access account to download the package.

NOTE:

These steps only apply to the S4810–ON and S6000–ON platforms.

Enter the onie-discovery-stop command to stop the ONIE discovery mode.

Assign an ip address to the management interface and verify the network connectivity.

ONIE:/ # ifconfig eth0 xx.xx.xx.xx/x

ONIE:/ #

ONIE:/ # ifconfig eth0

eth0

Link encap:Ethernet

inet addr:xx.xx.xx.xx

inet6 addr: fe80::92b1:1cff:fef4:9c76/64 Scope:Link

UP BROADCAST RUNNING MULTICAST

RX packets:18 errors:0 dropped:0 overruns:0 frame:0

TX packets:24 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:1000

RX bytes:1152 (1.1 KiB)

Interrupt:21 Memory:ff300000-ff320000

ONIE:/ # ping xx.xx.xx.xx

PING xx.xx.xx.xx (xx.xx.xx.xx): 56 data bytes

64 bytes from xx.xx.xx.xx: seq=0 ttl=62 time=1.357 ms

64 bytes from xx.xx.xx.xx: seq=1 ttl=62 time=0.577 ms

Upgrade the DIAG Installer. Again, boot to ONIE Rescue mode and install onie diag installer

NOTE:

The command onie-nos-install, shown in bold, is not available in S4810-ON ONIE version 1.0.0.1; instead use

the install_url ONIE:/bin # install_url command.

ONIE:/ # onie-nos-install tftp://xx.xx.xx.xx/ON-DIAG/S4810/JUL-08-2014/diag-installer-

powerpc-dell_s4810_on_p2020-r0.bin

Stopping: discover... done.

Info: Fetching tftp://xx.xx.xx.xx/ON-DIAG/S4810/JUL-08-2014/diag-installer-powerpc-

dell_s4810_on_p2020-r0.bin ...

ON-DIAG/S4810/JUL-08 100% |*******************************| 1361k 0:00:00 ETA

ONIE: Executing installer: tftp://xx.xx.xx.xx/ON-DIAG/S4810/JUL-08-2014/diag-installer-

powerpc-dell_s4810_on_p2020-r0.bin

Verifying image checksum ... OK.

Preparing image archive ...

Preparing image archive ...sed -e '1,/^exit_marker$/d' /installer | tar xf - OK.

Diag Installer: platform: powerpc-dell_s4810_on_p2020-r0

HWaddr 90:B1:1C:F4:9C:76

Bcast:xx.xx.xx.xx

MTU:1500

TX bytes:6864 (6.7 KiB)

Mask:xx.x.x.x

Metric:1

ONIE diagnostics