Allied Telesis AT-PWR3202 Instrukcja instalacji

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Zasilanie Allied Telesis AT-PWR3202. Allied Telesis AT-PWR3202 2 stron. Allied telesis at-pwr3202 power supply installation guide
Również dla Allied Telesis AT-PWR3202: Arkusz danych (1 strony)

Drukuj stronę
AT-PWR3202 Power Supply Installation Guide
Overview
AT-PWR3202 Power Supply is designed to be installed in an AT-RPS3204
Redundant Power Supply (RPS). The RPS can supply power to Allied Telesis
switches if the switch's main power supply fails
.
ST A
TU S
AT -P
W R 32
12 VD
C
02
,16 .6A
MA X
PO W
ER
FA UL
T
892
Verifying Package Contents
Verify that the correct components are included in your package:
•
AT-PWR3202 Power Supply
•
One 21-pin D-combo connector cable
•
This installation guide
If any item is missing or damaged, contact your Allied Telesis sales
representative for assistance.
Warranty
The AT-PWR3202 Power Supply has a Lifetime Year Warranty (Five Years
Power Supply and Fan). For detailed warranty information, see the
www.alliedtelesis.com website.
Installing the Power Supply
To install an AT-PWR3202 Power Supply, perform the following procedure:
1. Remove the AT-PWR3202 unit from its shipping package and store the
package in a safe place. You must use the original package if you need to
return the power supply to Allied Telesis.
*613-000397 Rev B*
PN 613-000397 Rev. B
2. On the back of the AT-RPS3204 unit, locate the power switch that
corresponds to the slot where you are going to install the power supply and
verify that the On/Off button is in the Off (out) position. From left to right on
the back, the power supplies are identified as B2, B1, A2, A1. (An AT-
RPS3204 is shipped with one AT-PWR3202 in the slot marked A1.)
3. Using a Phillips head screwdriver, remove the cover from the slot in the front
of the AT-RPS3204 unit where you want to install the power supply.
Note
As an example, the following steps show an AT-PWR3202 unit installed in
slot A2 of the AT-RPS3204 Redundant Power Supply.
ST AT
ST AT
U S
U S
AT -P
W R 32
12 VD
C
02
,16 .6A
MA X
PO W
PO W
ER
ER
FA UL
FA UL
T
T
Keep the slot cover in a safe area in case you remove a power supply. The
slot cover helps maintain proper air flow through the RPS.
4. Slide the AT-PWR3202 Power Supply into the slot
ST AT
ST AT
US
US
AT -P
12 VD
W R 32
C
02
,16 .6A
MA X
PO W
PO W
ER
ER
FA UL
FA UL
T
T
ST AT
US
AT -P
W R 32
12 VD
C
02
,16 .6A
MA X
PO W
ER
FA UL
T
1
5. Use a Phillips head screwdriver to tighten the captive screws.
S TA
S TA
TU S
TU S
A T- P
12 VD
W R 32
C
,16 .6A
PO W
PO W
ER
ER
FA UL
FA UL
T
T
6. On the back of the AT-RPS3204 unit, plug one end of the 21-pin D-combo
connector cable into the connector that corresponds to the slot in which you
installed the AT-RPS3202 Power Supply.
893
ON
OF F
7.
Tighten the captive screws.
ON
OF F
A 2
894
2
02
MA X
S TA
TU S
A T- P
W R 32
12 VD
C
02
,16 .6A
MA X
PO W
ER
FA UL
T
895
A 2
R P S
O U T
P U T
12 VD
A 2
C
A C IN
P U T
A 2/ A
10 0
- 24 0
1
VA C
~
R P S
O U T
P U T
12 VD
A 1
A 1
C
198
R P S
O U T
P U T
12 VD
A 2
C
A C IN
P U T
10 0
A 2 /A
- 24 0
1
VA C
~
R P S
O U T
P U T
A 1
12 VD
A 1
C
199
ON
OF F
ON
OF F
3