ALLNIC AUDIO A-5000 DHT Instrukcja obsługi - Strona 5
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Wzmacniacz ALLNIC AUDIO A-5000 DHT. ALLNIC AUDIO A-5000 DHT 9 stron. 300b single-ended pure direct heated triode monoblock power amplifier
Również dla ALLNIC AUDIO A-5000 DHT: Instrukcja obsługi (13 strony)
Drukuj stronę
WHAT'S IN THE BOX?
Please check that the shipping box contains the
following:
One (1) Allnic A-5000 DHT monoblock power
amplifier
One (1) IEC type power cord
One (1) Owner's Manual
Note:
1)
The A-5000 DHT ships with the tubes installed.
2)
The A-5000 DHT will work with most IEC type
aftermarket power cords. Of course, only you
can determine the power cord that works most
synergistically with the A-5000 DHT in your
system.
3)
Be sure the A-5000 DHT is labeled for the AC
voltage of your location. If it is not, please
contact Allnic Audio USA.
We advise that you keep the boxes and other packing
materials that your A-5000 DHT came in. It will be
useful if you sell your A-5000 DHT or in the unlikely
event you need to ship it for service.
SAFETY
Remove ALL protective cushioning material
inside the tube chimneys before operation. The
tube chimneys should contain NOTHING except
the tubes.
Disconnect the power cord by pulling the plug, not
the cable.
Do not attempt any repairs. Do not remove the unit's
chassis
cover
from Allnic Audio USA.
Keep the power cord away from heat sources
Keep the unit away from liquids – do not allow any
liquid to enter the interior of the unit.
When the unit is moved from a cold to a warm
environment,
condensation to evaporate before plugging the
A-5000 DHT into an AC connection.
Do not attempt any repairs.
See the notes on "Location, Location, Location".
without
specific authorization
allow
sufficient
time
CLEANING
A.
Chassis and glass
Use only a soft, lint-free cloth, dampened slightly with
water only (NO cleaning fluids!), to clean the faceplate,
chassis and tube chimneys of the A-5000 DHT.
B.
Connectors
You may use any good quality contact cleaner
recommended for such applications to clean the contacts
from time to time, as you deem appropriate.
INITIAL SET-UP
A.
LOCATION, LOCATION, LOCATION
Like all audio products using tubes, the Allnic Audio A-5000
DHT needs to be placed on a solid stand in a location that
provides good air circulation around, above and below the
monoblock.
DO NOT cover the top of the A-5000 DHT.
DO NOT place the unit on carpet or foam.
DO NOT subject the unit to knocks and shocks as you
move it around. This advice is meant particularly for
those who may want to place the A-5000 DHT on
some kind of after-market isolation feet or similar
devices. Dropping one side of the A-5000 DHT, or the
whole of the unit, is not a good thing to do.
DO NOT place the unit near a strong light or heat
source.
DO NOT place anything heavy on the unit.
DO NOT allow rubber or vinyl materials to rest on
the chassis for long periods of time. This could
discolour the metal.
DO place the unit on a shelf or stand that is stable
and not subject to vibration or sudden shock.
DO consider using a high quality power cord, inter-
connects and speaker cables. The A-5000 DHT is a
highly sensitive piece of electronic designed for
neutrality and will output what you put into it.
for
any
DO try to place A-5000 DHT away from major
sources and potential receivers of RFI and EMI.
Though well shielded, the A-5000 DHT will function
best away from large power transformers and other
sources of such interference and from other
equipment that could be susceptible to such forms
5