Miller ArcReach 16 Instrukcja obsługi - Strona 9

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla System spawania Miller ArcReach 16. Miller ArcReach 16 48 stron.

Drukuj stronę

CYLINDERS can explode if

damaged.

Compressed gas cylinders contain gas under high

pressure. If damaged, a cylinder can explode.

Since gas cylinders are normally part of the wel-

ding process, be sure to treat them carefully.

� Protect compressed gas cylinders from excessive heat, mechani-

cal shocks, physical damage, slag, open flames, sparks, and arcs.

� Install cylinders in an upright position by securing to a stationary

support or cylinder rack to prevent falling or tipping.

� Keep cylinders away from any welding or other electrical circuits.

� Never drape a welding torch over a gas cylinder.

� Never allow a welding electrode to touch any cylinder.

1-3.

Additional Hazards For Installation, Operation, And Maintenance

FIRE OR EXPLOSION hazard.

� Do not install or place unit on, over, or near com-

bustible surfaces.

� Do not install unit near flammables.

� Do not overload building wiring - be sure power

supply system is properly sized, rated, and protected to handle

this unit.

FALLING EQUIPMENT can injure.

� Use lifting eye to lift unit and properly installed ac-

cessories only, NOT gas cylinders. Do not exceed

maximum

Specifications).

� Use correct procedures and equipment of adequate capacity to lift

and support unit.

� If using lift forks to move unit, be sure forks are long enough to ex-

tend beyond opposite side of unit.

� Keep equipment (cables and cords) away from moving vehicles

when working from an aerial location.

� Follow the guidelines in the Applications Manual for the Revised

NIOSH Lifting Equation (Publication No. 94-110) when manually

lifting heavy parts or equipment.

OVERUSE can cause

OVERHEATING.

� Allow cooling period; follow rated duty cycle.

� Reduce current or reduce duty cycle before start-

ing to weld again.

� Do not block or filter airflow to unit.

FLYING SPARKS can injure.

� Wear a face shield to protect eyes and face.

� Shape tungsten electrode only on grinder with

proper guards in a safe location wearing proper

face, hand, and body protection.

� Sparks can cause fires — keep flammables away.

STATIC (ESD) can damage PC

boards.

� Put on grounded wrist strap BEFORE handling

boards or parts.

� Use proper static-proof bags and boxes to store,

move, or ship PC boards.

lift

eye

weight

rating

� Never weld on a pressurized cylinder — explosion will result.

� Use only correct compressed gas cylinders, regulators, hoses,

and fittings designed for the specific application; maintain them

and associated parts in good condition.

� Turn face away from valve outlet when opening cylinder valve. Do

not stand in front of or behind the regulator when opening the

valve.

� Keep protective cap in place over valve except when cylinder is in

use or connected for use.

� Use the proper equipment, correct procedures, and sufficient

number of persons to lift, move, and transport cylinders.

� Read and follow instructions on compressed gas cylinders, asso-

ciated equipment, and Compressed Gas Association (CGA) publi-

cation P-1 listed in Safety Standards.

MOVING PARTS can injure.

� Keep away from moving parts.

� Keep away from pinch points such as drive rolls.

WELDING WIRE can injure.

� Do not press gun trigger until instructed to do so.

� Do not point gun toward any part of the body, other

people, or any metal when threading welding wire.

BATTERY EXPLOSION can injure.

(see

� Do not use welder to charge batteries or jump start

vehicles unless it has a battery charging feature

designed for this purpose.

MOVING PARTS can injure.

� Keep away from moving parts such as fans.

� Keep all doors, panels, covers, and guards closed

and securely in place.

� Have only qualified persons remove doors, panels,

covers, or guards for maintenance and troubleshooting as

necessary.

� Reinstall doors, panels, covers, or guards when maintenance is

finished and before reconnecting input power.

READ INSTRUCTIONS.

� Read and follow all labels and the Owner's Manual

carefully before installing, operating, or servicing

unit. Read the safety information at the beginning

of the manual and in each section.

� Use only genuine replacement parts from the manufacturer.

� Perform installation, maintenance, and service according to the

Owner's Manuals, industry standards, and national, state, and lo-

cal codes.

H.F. RADIATION can cause

interference.

� High-frequency (H.F.) can interfere with radio navi-

gation, safety services, computers, and communi-

cations equipment.

� Have only qualified persons familiar with electronic equipment per-

form this installation.

� The user is responsible for having a qualified electrician promptly

correct any interference problem resulting from the installation.

� If notified by the FCC about interference, stop using the equipment

at once.

OM-278792 Page 3