AquaScape 91010 Instrukcja i konserwacja - Strona 5

Przeglądaj online lub pobierz pdf Instrukcja i konserwacja dla Pompa wodna AquaScape 91010. AquaScape 91010 16 stron.

Drukuj stronę

• It is recommended that the pump NOT be positioned in

the deepest area of the pond. This will protect the fish

by preventing the pond from completely draining in the

case of a leak in the plumbing or filter. If needed, bricks or

stones can be used to raise the pump off the bottom of

the pond.

• The Ultra Water Pump includes an assortment of fittings

for a wide variety of plumbing options. Select and install

the appropriate fitting(s) for your application.

• The included Multi-Hose Adapter(s) is (are) designed to

accommodate different diameters of tubing and ideal for

applications using a single plumbing line.

• The Multi-Hose Adapter can

be threaded directly into the

discharge of the pump

(Ex. 3).

• If using a diameter of pipe

that is larger than the

smallest section of the Multi-

Hose Adapter, trim off the

smaller sections to prevent

flow restriction (Ex. 4).

• The included threaded

FPT 90° elbow allows the

water flow to be directed

horizontally, perfect for

fountain basin applications

where vertical space is

limited (Ex. 5).

• To install the elbow, attach

the included MPT Coupling

to the discharge of the

pump. Then thread the

collared elbow fitting to the

MPT Coupling to attach it to

the pump.

• The collared connections

allow the pump to be quickly

and easily disconnected

from the tubing for pump

removal or maintenance.

• The convenient included 1/2" Valve (400/550/800) (Ex. 6)

or 3/4" 3-Way Valve (1100/1500/2000) (Ex. 7) provide the

ability to customize flow rates.

Ex. 6

☎

aquascapeinc.com |

CAN (866) 766-3426 |

• The included flow control

valve can be installed directly

into the pump discharge or

installed horizontally using

the threaded FPT 90° elbow

(Ex. 8).

• Once installed, simply adjust

the valve(s) to dial in the

desired water flow.

• When using the 3-Way Valve, close off any unused valves

to maximize water flow to the valves in use.

• Attach the tubing to the

selected fitting(s) (Ex. 9)

using a twisting motion

(Ex. 10). If the tubing fits

loosely, a hose clamp (not

included) can be used to

secure the attachment.

• In some instances the tubing

may be difficult to attach to

Ex. 3

the selected fitting. If this is

the case, we recommend

heating the hose with a

hair dryer or simply dipping

the hose in very hot water

for a few seconds prior to

attachment. Lubrication

can also be used; we

recommend silicone grease

or olive oil.

Ex. 4

• Connect the other end of the pump tubing to the

decorative fountain or pond filter.

• Connect the pump to

an outlet (Ex. 11) that is

protected by a ground fault

circuit interrupter (GFCI).

Once the pump is running

and water is circulating,

check for leaks where the

Ex. 5

external connections are

made.

General Maintenance

• We recommend inspecting your pump on a regular basis

to make sure it is functioning properly. If water flow is

reduced, it may be due to

the filter screen or sponge

being clogged with debris.

• The front screen can be

removed by twisting the

locking knob counter-

clockwise and pulling the

Ex. 7

screen off (Ex. 12).

☎

US (866) 877-6637

Ex. 8

Ex. 9

Ex. 10

Ex. 11

Ex. 12