Diamond DRCS-24 Instrukcja instalacji i obsługi - Strona 9
Przeglądaj online lub pobierz pdf Instrukcja instalacji i obsługi dla Urządzenia kuchenne Diamond DRCS-24. Diamond DRCS-24 11 stron. Carving station
Drukuj stronę
MAINTENANCE
WARNING
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them
to operate safely in Hatco equipment. It is essential
to use Hatco Replacement Parts when repairing
Hatco equipment. Failure to use Hatco Replacement
Parts may subject operators of the equipment to
hazardous electrical voltage, resulting in electrical
shock or burn.
WARNING
If service is required on this unit, contact your
Authorized Hatco Service Agent, or contact the
Hatco Service Department at 800-558-0607 or
414-671-6350; fax 800-690-2966 or International fax
414-671-3976.
WARNING
This product has no "user" serviceable parts. To
avoid damage to the unit or injury to personnel, use
only Authorized Hatco Service Agents and Genuine
Hatco Parts when service is required.
CLEANING
The Hatco Glo-Ray Carving Stations are designed for
maximum durability and performance, with minimum
maintenance.
WARNING
To prevent electric shock, always unplug the Glo-Ray
Carving Station before performing any cleaning or
maintenance.
To preserve the bright finish of the Carving Station, it is
recommended that the surfaces be wiped daily with
a damp cloth. Stubborn stains may be removed with
a stainless steel cleaner or a non-abrasive cleanser.
CAUTION
Use only non-abrasive cleaners. Abrasive cleaners
could scratch the finish of your Glo-Ray Carving
Station marring its appearance and making it
susceptible to soil accumulation.
CAUTION
Unit is not waterproof. DO NOT submerge in water.
Do not operate if it has been submerged in water.
Form No. GRCSM-0401
Drip pans should be removed from the foodwarmer for
washing and sanitizing after each use.
To maintain your cutting board, clean with mild
detergent and rinse. Apply a coating of mineral oil to all
surfaces, allowing oil to penetrate for a short period.
Wipe off any excess oil from surface.
To avoid damage to cutting board do not allow board
to be immersed in water or run through
a dishwasher. Damage to cutting board is not
covered under warranty.
Breath protector(s) may be removed for thorough
cleaning and polishing. They should be wiped daily with
a soft, damp cloth. If fine scratches are present, a good
polycarbonate cleaner may be used to polish the breath
protector(s) and remove any scratches.
Only soft cleaning cloths should be used to clean
breath protector(s). Breath protector(s) are made of
shatterproof polycarbonate and will scratch if proper
care is not taken.
DISPLAY LIGHT BULB REPLACEMENT
The display light is an incandescent bulb which
illuminates the warming area. This bulb has a special
coating to guard against injury and food contamination
in the event of breakage.
To replace a bulb, disconnect the power supply and wait
until the unit has cooled. Display lamps have a threaded
base. Unscrew the bulb from the unit and replace it with
a new specially coated incandescent bulb. Hatco
shatter-resistant bulbs meet N.S.F. standards for food
holding and display areas.
NOTE: Hatco shatter-resistant light bulbs meet N.S.F.
standards for food holding and display areas. For 100
& 120 Volt applications, use Hatco part #02.30.043.00.
For 220 & 240 Volt applications, use Hatco part
#02.30.058.00.
Only bulbs which meet or exceed N.S.F. standards,
specifically designed for food holding areas must be
used. Breakage of bulbs not specially coated could
result in personal injury and/or food contamination.
6
CAUTION
CAUTION
WARNING