Aquatec AquaPro AP6000HM Instrukcja obsługi - Strona 2

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Pompa wodna Aquatec AquaPro AP6000HM. Aquatec AquaPro AP6000HM 2 stron.

Drukuj stronę

Congratulations on your purchase of this product by AquaPro,

the answers for your watergarden made easy!

VOLTAGE (V)

POWER (WATTS)

MAX HEIGHT (M)

FLOW MAX (L/H)

CABLE LENGTH (M)

DESCRIPTION AND FEATURES

Your Aquapro Waterfeature pump has been

manufactured with advanced technology to

provide you with the best quality pump for

your pond or water feature.

• Aquapro pumps are suitable for use in

many different applications including;

fountains, water features, small ponds

and hydroponics.

• Your Aquapro pump has a single moving

part (an impellor set) therefore enabling

easy cleaning and maintenance.

• The motor and electrical components are

encapsulated in epoxy resin, ensuring

safe operation under water.

• The pump has a robust bearing and

shaft design so no oil/grease lubrication

is required.

• The Aquapro pumps that have plastic

encased impellor parts and ceramic

shafts (no exposed metal) may be used

in salt water applications.

• Check out the Aquapro range of pond

lights and accessories.

AP6000HM

AP7500HM

240

150

4.00

4.20

6000

7500

INSTALLATION

1. If required, have a qualiﬁed electrician

install weatherproof power point near

to the pond or water feature, (within the

cable length of the pump).

2. Place the pump in desired location,

ensure it is on a stable surface free of

sludge/debris and connect tubing to

the outlet.

3. Ensure pump is submerged, then plug

in power cord and switch on.

MAINTENANCE

Disconnect power cord from the power

supply before performing maintenance.

Never lift the pump by the power cord.

The only serviceable item is the impellor set.

The motor unit of the pump is

encapsulated with epoxy resin and does

not need lubrication.

All Aquapro submersible pumps are water

cooled; if pump becomes restricted it

will overheat and could cause permanent

damage. Ensure pump does not become

blocked or restricted.

The power cord cannot be replaced. If

the cord is damaged, the pump must be

discarded.

The impellor set is a wearing consumable

part. Regular inspections, cleaning and

maintenance of impellor is necessary to

ensure longer impellor life.

If the impellor set becomes worn or

damaged it should be replaced (available

from your dealer or special orders). Failure to

do so may cause serious damage to pump.

1. Disconnect the power cord before

performing maintenance.

2. Remove front ﬁlter cage by gently

squeezing sides.

3. Unscrew the four large screws facing

the rear of the motor and remove the

impellor housing.

1 Outer Filter Screen

2 Inner Filter Screen

3 Impellor Cover/ Housing

4 Impellor Assembly

5 Motor Body

6 Stepped Outlet Hosetail

AP7500 Model shown. Picture for illustration purposes only..

MULTI-USE PUMPS

INSTRUCTIONS MANUAL

4. Gently remove o'ring seal and impellor

set. Clean the impellor and impellor

chamber, taking care not to damage or

scour surfaces. Check for any signs of

wear or damage.

5. Reinstall the complete impellor set,

making sure the locator probe ﬁts into

the hole on the impellor set. Put the

impellor set in ﬁrmly. Carefully replace

o'ring seal. Check the impellor can

spin freely.

6. Put impellor housing back on and screw

the four screws back in, making sure

the screws are done up evenly.

7 . Replace front ﬁlter cage, re-attach

outlet, submerse in water and turn on.