aquatherm 50337 Instrukcja obsługi i konserwacji - Strona 8

Przeglądaj online lub pobierz pdf Instrukcja obsługi i konserwacji dla Akcesoria spawalnicze aquatherm 50337. aquatherm 50337 8 stron. Fusion for aquatherm green pipe, aquatherm blue pipe, aquatherm lilac pipe, aquatherm red pipe and aquatherm ti pipesystems from 16 up to 125 mm

sAfETY sTANDARDs

1. This equipment must only be used in full compliance with the instructions
given in this manual. All other uses are to be considered improper and
forbidden. Improper use may cause injury to the machine operator or third
parties and/ or cause damage to the machine or other objects.
2. All standards concerning health and safety in the workplace must be
implemented at all times.
3. Before using the machine personnel must be properly trained in its
operation and in applicable accident-prevention regulations.
4. The components used in the construction of the machine and its
operating principles are such that special care should be taken to carry out
the following instructions:
4.1. Electric power supply:
Make sure the mains electricity supply is suitable for the machine. Do
not use an electricity supply which is subject to voltage surges or drops.
Use a guaranteed mains supply or power generators fitted with voltage
stabilizers. Make sure the machine's power socket is protected with a high
sensitivity differential switch (IΔ=30 mA) and that the machine has an
earth connection.
4.2. Electricity:
Even if designed and manufactured in full accordance with applicable
standards and fitted with all the required safety devices, electrically
powered machinery nonetheless poses a risk to safety due to the nature of
this type of energy (i.e. risk of electric shock). Do not expose the machinery
and its electrical cables to the rain, to chemicals, to mechanical stress (e.g.
vehicles driving across the cables). Use perfectly dry pipes and connectors.
Do not use the machine if your hands are wet or the workplace is moist
or damp.
4.3. Avoiding burns:
Do not touch the heating element, metal components or plastic parts close
to the welding surface during heating, welding or cooling, since the plate
reaches very high temperatures. Operate the machine with the utmost
care. Wear heatproof gloves and protective clothing suitable for
preventing burns.
4.4. The workplace:
Make sure that unauthorized persons are unable to gain access to the
workplace. The workplace must be clean, tidy, properly ventilated and
well lit. There should not be any gases, fumes or flammable materials
present, such as solvents, oils, paints, etc. These may constitute a fire risk
if they come close to the heating element. Keep any objects or materials
susceptible to heat damage well away from the machine. When working
in tight, awkward places an external supervisor must be present to provide
assistance to the machine operator in case of need.
4.5. Checks and repairs:
Before using the machine check that no components are damaged.
Replace cables or components as soon as they become worn. Repairs
must be carried out only by an expert or specially trained technician using
exclusively original spare parts. Dismantling the machine involves a risk of
electric shock. No alterations may be made to the machine.
4.6. Presence of the operator at all times during operation:
The machine operator must not leave the machine while it is welding or
heating up.
aquatherm GmbH • Biggen 5 • 57439 Attendorn • www.aquatherm.de
4.7. Use pipes that are chemically inert: Do not carry out any welding
operations on pipes containing, or which may have contained, substances
which when heated generate explosive gases or other gases dangerous to
the human body.
4.8. Support: Position the welding machine using only the proper fork or
bench supports.
4.9. Take care with cables: Do not disconnect plugs, sockets or connectors
or move the machine by pulling on the electric cables.
4.10. Finally...: After work, remember to disconnect the welding machine
from the mains or supply socket.
4.11. The machine must not be used in areas where there is a risk of
explosion or fire. Only specially designed and manufactured machines must
be used in workplaces of this kind.
5. The manufacturer and dealer will not be liable for personal injury or
damage to property arising from the improper use of the machine.
6. wARNINg
In the event of a fault of any kind during the guarantee period, send
the machine to the manufacturer or an authorized repair centre. Having
repair work carried out by personnel not authorized by aquatherm will
immediately invalidate the warranty