3Com 3C16411 - Baseline Dual Speed Hub Podręcznik użytkownika - Strona 5
Przeglądaj online lub pobierz pdf Podręcznik użytkownika dla Przełącznik 3Com 3C16411 - Baseline Dual Speed Hub. 3Com 3C16411 - Baseline Dual Speed Hub 9 stron. Baseline dual speed hubs
Również dla 3Com 3C16411 - Baseline Dual Speed Hub: Arkusz danych (2 strony)
Drukuj stronęM
OUNTING
The Baseline Dual Speed Hub is supplied with two mounting brackets and
four screws. These are used for rack mounting the unit. When mounting
the unit, you should take note of the guidelines given in "Positioning the
Baseline Dual Speed Hub"on page 3.
The Baseline Dual Speed Hub is 1U high and will fit a standard 19-inch
rack.
CAUTION: Disconnect all cables from the unit before continuing.
Remove the self-adhesive pads from the underside of unit, if
already fitted.
To rack mount the unit:
1
Place the unit the right way up on a hard, flat surface with the
front facing towards you.
2
Locate a mounting bracket over the mounting holes on one side of
the unit, as shown in the diagram.
3
Insert the two screws supplied in the mounting kit and fully tighten
with a suitable screwdriver.
4
Repeat the two previous steps for the other side of the unit.
5
Insert the unit into the 19-in. rack and secure with suitable screws
(not provided).
6
Reconnect all cables.
P
ROBLEM
Refer to the information about LEDs given earlier in this guide to see if
the problem can be identified and rectified. If the problem persists and
the Baseline Dual Speed Hub still does not operate successfully, contact
your supplier with the following information before returning the unit:
Product number and serial number
(printed on a label on the rear of the unit)
A brief description of the fault
T
ECHNICAL
Related Standards
The SuperStack 3 Baseline Dual Speed Hub has been designed to the
following standards:
Functional
ISO/IEC 8802-3, IEEE 802.3, IEEE 802.3u, IEEE 802.1D
Safety
UL 1950, EN 60950, CSA 22.2 #950, IEC 60950
EMC Emissions
EN 55022 Class A, VCCI Class A, AS/NZS 3548 Class A,
FCC Part 15 Class A, ICES-003 Class A, CNS 13438,
EN61000-3-3, EN61000-3-2.
Immunity
EN55024
Physical
Width
440 mm (17.3 in.)
Depth
173 mm (6.8 in.)
Height
44 mm (1.7 in.) or 1 U
Weight
3C16410: 2.22 kg (4.90 lb)
3C16411: 2.6 kg (5.8 lb)
Mounting
Free standing, or 19 in. rack mounted using the mounting
kit supplied
K
I
IT
NSTRUCTIONS
S
OLVING
I
NFORMATION
When returning any equipment to your supplier ensure that the
equipment is packed suitably for transit.
Some older NIC (network interface card) cards were developed
before the standardization of the auto-negotiation protocol.
These may cause the Baseline Dual Speed Hub to sense the
speed of the network incorrectly. We strongly recommend that
you install the latest versions of the NIC drivers before
connecting your network. 3Com NIC card drivers dated before
23/03/95 should be updated from the 3Com website.
Electrical
Power Inlet
AC Line Frequency
Power Consumption
Power Dissipation
Input Voltage
Current Rating
Environmental
Operating Temperature
Humidity
5
IEC 320
50/60 Hz
3C16410: 8.5 VA
3C16411: 9.5 VA
3C16410: 29 BTU/hr
3C16411: 32.4 BTU/hr
100–240 V AC
3C16410: 1.0 A (maximum)
3C16411: 1.0 A (maximum)
0–40 °C (32–104 °F)
0–95 % (non-condensing)