Panasonic SA-HC7 Instrukcja obsługi - Strona 27

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla System stereo Panasonic SA-HC7. Panasonic SA-HC7 32 stron. Compact stereo system model no. sc-hc7

Drukuj stronę

Troubleshooting guide

Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the remedies

indicated in the chart do not solve the problem, consult your dealer for instructions.

Common problems with the whole system

■

All operations are ignored although

the unit is on.

The display changes when the unit

is in standby mode.

The Demo Mode is automatically

activated after plugging/unplugging

the AC mains lead.

The power indicator does not go off

even in the Power-save Mode.

The power indicator lights red when

the AC mains lead is connected in

Power-save Mode.

It takes time to turn the unit on

although the Quick-Start Mode is

set.

Cannot connect to network.

• "Cannot connect to the network."

is displayed.

• The title obtaining display

(Gracenote

) does not goes off.

• CD titles cannot be obtained.

• The IP address, etc. cannot be

obtained although the wireless

LAN is connected.

• The router does not respond, the

indicator does not light.

etc.

"Cannot ﬁ nd the shared folder." is

displayed.

"Cannot ﬁ nd a track that can be imported

in the shared folder." is displayed.

"Cancelled by timeout." is

displayed.

"Cancelled. Cannot ﬁ nd the input

PC name." is displayed.

"Cannot connect to the network." is

displayed.

"Cancelled. Unknown error

occurred." is displayed.

Press [8] on the unit more than 10 seconds and restart the unit. Or pull out the AC mains

lead, wait a few minutes to reconnect the cord and turn the unit on.

Press [g] (stop) on the unit until "Cancel Demo" is displayed.

Switch the Demo Mode to "Off" on the setting menu.

If there exists recording data that has not been converted/analysed, the unit enters Quick-Start

Mode in standby mode. When Convert/Analyse is complete, the unit switches to the Power-

save Mode.

The AC mains lead was unplugged immediatly after the unit was turned off last time. If there

exists recording data that has not been converted/analysed, the unit enters in Quick-Start

Mode when the unit is in standby mode: When Convert/Analyse is complete, the unit switches

to the Power-save Mode.

It is necessary to perform the system process to stabilize the unit's operations several tens of

seconds while the unit is in standby mode. If the unit is turned on during this process, it takes

time until the unit starts to operate. Also, the power indicator (red) may go off for a moment,

the clicking sound may be heard.

Connect the LAN cable properly.

You connected the telephone cable to the LAN port on this unit. Connect the straight type of

LAN cable.

Are the modem and broadband router ON? Turn off the modem and broadband router just in

case, turn them on again and wait for several minutes. Then turn the unit on again to obtain

the titles.

You made the setting to use only the internal CD Database. Set to "Yes" on the setting menu

"CD Database Setting".

Wrong network settings. Make the settings following the instructions of your provider or

telephone carrier. To establish the connection authentication of the router itself, you may

need to enter the connection account/connection user name/connection password, etc. on the

computer. If they are not clear, contact your provider or telephone carrier.

Wrong broadband router settings. Refer to the instruction manual of the broadband router as well.

The broadband router or modem connection is wrong. Read operating instructions for each

device carefully and connect them properly.

You changed the network connection configuration such as exchange of the broadband router.

Network connection may not be possible for 10 minutes after changing the configuration. Wait

for 10 minutes or press [8] on the unit approx. 10 seconds to restart.

If you are using the wireless LAN, the authentication setting between main device (access

point) and subdevice (LAN port connection type) is necessary. Make the setting according to

the instructions of wireless LAN device. (We recommend checking the PC setting and wireless

LAN connection operation first.)

The characters used for the folder name on the computer may be invalid. Only alphanumeric

characters and symbols (4 types) can be used. If different types of user name/password are

used, change to the above characters.

The characters used for the folder name on the computer may be different. Check the folder

name on the computer.

The folder setting on the computer may be insufficient. Sharing setting might not have been

made or may be incomplete. Check the setting content again.

The folder setting on the computer may be insufficient. Shared level may be insufficient.

Check the setting content again.

Check if the router, modem, etc. are ON. Check the connection and settings for the router and

this unit.

Check if the computer is ON.

The input PC name is wrong. Confirm your computer's PC name and enter the name correctly.

The cable is not connected. Check the connection to the computer.

Check the LAN cable connection. Also check if the router, modem, etc. are ON.

Turn on the device connected to this unit again and perform the operation again.

Pages

—

6, 23

—

19, 20

—

19, 20

—