Bionaire BCH9212U10EM1 Ulotka z instrukcją - Strona 2

Przeglądaj online lub pobierz pdf Ulotka z instrukcją dla Grzałka elektryczna Bionaire BCH9212U10EM1. Bionaire BCH9212U10EM1 2 stron. Heater with advanced digital thermostat

Drukuj stronę

Bionaire BCH9212U10EM1 Ulotka z instrukcją

P L E A S E R E A D A N D S AV E T H E S E

I M P O R TA N T S A F E T Y I N S T R U C T I O N S

When using electrical appliances, basic safety precautions should

12. Use appliance only for intended household use as

always be followed to reduce the risk of fire, electric shock, and

described in this manual. Any other use not

injury to persons, including the following:

recommended by the manufacturer may cause fire,

1. Read all instructions before using the appliance.

electric shock, or injury to persons. The use of

2. To avoid fire or shock hazard, plug the appliance directly

attachments not recommended or sold by the

into a 120V AC electrical outlet.

manufacturer may cause hazards.

3. The heater is hot when in use. To avoid burns, DO NOT let

13. DO NOT use outdoors.

14. To prevent a possible fire, DO NOT block air intakes or

bare skin touch hot surfaces. If provided, use handles when

moving this heater. Keep combustible materials, such as

exhaust in any manner. DO NOT use on soft surfaces, like

furniture, pillows, bedding, papers, clothes, and curtains at

a bed, where openings may become blocked.

least 3 feet (0.9 m) from the front of the heater and keep

15. To disconnect heater, turn controls to OFF, then remove

them away from the sides and rear.

plug from outlet.

4. DO NOT run cord under carpeting. DO NOT cover cord

16. Avoid the use of an extension cord because the

with throw rugs, runners, or the like. Arrange cord away

extension cord may overheat and cause a risk of fire.

from traffic area and where it will not be tripped over.

However, if you have to use an extension cord, the cord

5. This heater is not intended for use in bathrooms,

shall be No. 14 AWG minimum size and rated not less

laundry areas and similar indoor location. NEVER locate

than 1875 watts.

heater where it may fall into a bathtub or other water

17. If the heater will not operate, see specific instructions on

container.

Auto Safety Shut-off.

6. Extreme caution is necessary when any heater is used

18. DO NOT attempt to repair or adjust any electrical or

by, or near children or invalids, and whenever the

mechanical functions on this unit. Doing so will void your

heater is left operating and unattended.

warranty. The inside of the unit contains no user

7. Always unplug the heater when not in use.

serviceable parts. All servicing should be performed by

8. When unplugging, be sure to pull by the plug and not

qualified personnel only.

the cord.

19. Discontinue use if plug or outlet is hot. It is

9. DO NOT insert or allow foreign objects to enter any

recommended that the outlet be replaced if plug or

ventilation or exhaust opening as this may cause an

outlet is hot to touch.

electric shock or fire, or damage the heater.

PLEASE READ AND SAVE

10. DO NOT operate heater with a damaged cord or plug, or

after the heater malfunctions, has been dropped or

THESE IMPORTANT SAFETY

damaged in any manner. Return appliance to

manufacturer for examination, electrical or mechanical

INSTRUCTIONS

adjustment, or repair.

11. A heater has hot and arcing or sparking parts inside. DO

NOT use it in areas where gasoline, paint, or flammable

liquids are used or stored.

THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the

other). To reduce the risk of electric shock, this plug is intended to fit in a

polarized outlet only one way. If the plug does not fit fully in the outlet,

reverse the plug. If it still does not fit, contact a qualified electrician to

install the proper outlet.

DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS

SAFETY FEATURE IN ANY WAY.

BCH9212-U_10EM1.indd 2

A S S E M B LY I N S T R U C T I O N S

TECHNICAL SPECIFICATIONS

Figure 1

• Amps: 12.5

• Wattage: 1500W (+5% –10%)

• Working voltage: 120V AC/60Hz

ASSEMBLY INSTRUCTIONS

Unpack your heater from the box, being careful to remove

all parts from plastic bags and remaining packaging. Please

save the carton for off-season storage.

Your heater is packed with separate base in the box. Carefully

remove all parts from plastic bags. To prevent scratches, place

Figure 2

all parts onto a cloth before assembly. Follow the below

instructions for Base assembly:

Base Assembly

Step 1:

If the base is in two halves, snap them together

by sliding slots of one base half into slots of

second base half. Refer to Figure 1.

Step 2:

Run the power cord through the center of the

assembled base. To assemble the base to the unit

(either one or two-piece base) first make sure

the side marked "Rear" is facing the back of the

heater. Line up holes of the base with holes on

Figure 3

bottom of heater housing, and secure with 4

provided screws. Refer to Figure 2.

Step 3:

Lace the power cord through the cord minders on

the underside of the base. Refer to Figure 3.

Step 4:

Turn the heater right side up on a flat level

surface prior to beginning operation.

F E AT U R E S - O P E R AT I O N S

communications. However, there is no guarantee that the

Remote Control

interference will not occur in a particular installation. If the

Unpack the remote control from box. This includes one lithium

product does cause harmful interference to radio or television

battery, CR2025/3V. Please note this remote control will not work

reception, which can be determined by turning the product on

through walls. Remove battery before discarding the remote.

or off, the user is encouraged to try to correct the

interference by one or more of the following measures:

NOTE: REMOVE THE PROTECTIVE COVER FROM THE BATTERY

• Reorient or relocate the receiving antenna.

PRIOR TO BEGINNING OPERATION.

• Increase the separation between the product and the

Battery Replacement

receiver.

1. Locate the battery cover on the back of the remote control

• Connect the product into an outlet on a circuit different

handset. Slide the battery cover out with your thumb.

from that to which the receiver is connected.

2. Place battery into battery compartment.

• Consult the dealer or an experienced radio/TV technician

3. Slide battery cover closed.

for help.

4. For your convenience, a remote control holder is

• Changes or modifications not expressly approved by the

integrated into the back of the heater housing.

party responsible for compliance could void the user's

NOTES:

authority to operate the equipment.

• THIS PRODUCT CONTAINS A BUTTON BATTERY. IF

SWALLOWED, IT COULD CAUSE SEVERE INJURY IN JUST 2

Figure 4

HOURS. SEEK MEDICAL ATTENTION IMMEDIATELY.

• Remove the battery from the equipment when it is not

being used for an extended period of time.

• Remove the used battery promptly.

• Do not discard used batteries into household trash

containers. Contact your local government for disposal or

recycling practices in your area.

FCC STATEMENT

Potential for Radio/Television interference

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) this device must

accept any interference received, including interference that

A Control Buttons

may cause undesired operation.

B LCD Display

This product has been tested and found to comply with the

C Dial Wheel

limits for a Class B digital device, pursuant to part 15 of the

D Power Light

FCC rules.

E Remote Control

These limits are designed to provide reasonable protection

against harmful interference in a residential installation. The

product generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

F E AT U R E S - O P E R AT I O N S

OPERATING INSTRUCTIONS

Thermostat Control

1. Place heater on a firm, level surface.

Your heater is equipped with a digital thermostat that allows

2. Plug heater into a standard outlet. Once plugged in, the

you to set your heater to a precise comfort level by turning

Power Light will illuminate.

the Dial Wheel on the control panel or pressing the arrow

NOTE: Avoid overloading your circuit by not using other

buttons on the remote control:

high wattage appliances in the same outlet. At 1500

Turn the Dial Wheel to activate. The Thermostat icon ( )

watts, this unit draws 12.5 Amps.

will appear on the LCD Display.

3. Operate heater by pressing the Power Button ( ) and

To preset a precise comfort level, turn the Dial Wheel to

selecting modes and settings according to preference.

NOTE: Remove the plastic film from the control panel

adjust the temperature from 85°F to 65°F (Default:

before using (if included).

"85"). The LCD Display will show the selected temperature

reading. When the preset temperature is reached, the heater

Power On/Off

will shut off and cool down for 15 seconds. When the room

Press the Power On/Off Button to turn the heater on. Once

temperature drops below the preset temperature, the heater

on, the heater will run in the Max Heat mode and the

will automatically turn on again to maintain the preset

Stay On icon will appear on the LCD Display. Press the

temperature level.

Power On/Off button to manually turn off the heater at any

FrostProtect™ Setting

setting.

Your heater is equipped with FrostProtect™. The heater

NOTE: The Power Light will remain illuminated while unit is

will turn on automatically when the room temperature drops

plugged in.

below 40°F. To activate FrostProtect™, turn the Dial Wheel to

Mode Selection

show "40" and the FrostProtect™ icon ( ) will appear

on the LCD Display.

Select your desired heat settings by pressing the

NOTE: It is normal for the heater to cycle on and off to

corresponding buttons as located on your heater or press the

Mode button on remote control to cycle through the heat

maintain the preset temperature. Raise the thermostat setting

settings. An indicator light will illuminate next to each button

or operate in Stay On mode to prevent the heater from

to indicate that the selected setting/mode is activated.

cycling. When the preset temperature is reached or when the

heater is shut off, the fan will run for 15 seconds without

Fan Only Setting

heat. This cool down process ensures an accurate and

Press the Fan Only Button to run the heater without heat

consistent temperature reading.

output. The Stay On icon will appear on the LCD Display.

NOTE: To shut the heater off at any setting, press the Power

Button ( ) until the LCD Display goes off. The heater will

– HIGH Heat Setting

cool down for 15 seconds, and the Fan Only indicator light

Press the Max Heat Button to run the heater continuously

will blink in Amber until cool down is completed. The digital

at 1500W. The Stay On icon will appear on the LCD Display.

thermostat has memory; it will remember the last

Eco-Smart™ Setting

temperature setting before the heater is turned off. However,

if the heater is unplugged, the digital thermostat will no

Press the Eco-Smart™ Button to activate the energy

longer remember the previous temperature setting. You will

efficient Eco-Smart™ Mode. The heater will now cycle

need to reset the digital thermostat if the heater is

between high (at 1500W) and low (at 750W) heat settings to

unplugged.

provide heat. The Stay On icon will appear on the LCD Display.

C L E A N I N G / M A I N T E N A N C E

A U T O S A F E T Y S H U T- O F F

AUTO SAFETY SHUT-OFF

Oscillation

This heater is equipped with a technologically-advanced

Press the Oscillation Button (

) on control panel or

safety system that requires the user to reset the heater if

remote control to activate or stop the oscillation feature.

there is a potential overheat situation. When a potential

NOTE: Please do not manually turn the heater on the base.

overheat temperature is reached, the system will

It is designed to turn only by motorized oscillation.

automatically shut the heater off. It can only resume

operation when the user resets the unit.

Timer

If the heater shuts down and the Power Light

Your heater is equipped with 24-Hour Auto Shut-off Timer

is flashing:

feature. This allows you to program your heater to shut off

1. Stand the heater upright.

automatically after running a defined time interval (from 0

2. Unplug the heater and allow 30 minutes for the heater

to 24 hours).

to cool down.

1. Press the Timer Button ( ) once. The indicator light will

3. After 30 minutes plug the heater in and operate

begin to blink for 5 seconds. The LCD Display will show

normally.

"0" and the "Hr" icon.

4. If the heater does not work normally, repeat steps 1, 2

2. Turn the Dial Wheel on the control panel to adjust from

and 3 again.

0 to 24 to select your desired time interval for the

NOTE: If the heater is plugged in again and Power On/Off

heater to shut-off automatically. The selected hour will

Button is pressed within the 30-minute cool down period,

appear on the LCD Display, and then the Timer indicator

heater will run at Max Heat setting, but shut down in 2

light will stop blinking in 3 seconds to indicate that the

seconds with the Power Light flashing. Please repeat the

selected timer is activated. The LCD Display will return to

above 4 steps to reset the heater again and ensure to allow

show the preset temperature and mode setting.

sufficient time for the thermostat to cool down.

3. To cancel the Timer feature, press the Timer Button ( )

twice within 5 seconds, the Timer indicator light will go

Tip Over Shut-Off:

off.

When the unit is accidentally knocked over, it will instantly

NOTE: The timer does not work with the FrostProtect

Setting.

shut off and the Power Light will flash. The unit may also

shut off if it is moved or bumped. To reset, simply place the

heater in an upright position, the Power Light will stop

CLEANING/MAINTENANCE

flashing and it will operate normally.

Always unplug the heater before cleaning and allow the

NOTE: If unit does not turn on when placed in the upright

heater to cool down.

position, press Power On/Off Button once and heater will

1. Clean the unit with a soft cloth moistened with a mild

resume operation.

soap and water solution.

2. NEVER use abrasive or flammable solvents to clean the

unit.

3. After cleaning, be sure to completely dry the unit with a

cloth or towel.

4. Store heater in a cool, dry location.

5. It is recommended that you store the unit in its original

carton.

TIP: Over time, dust may accumulate on the front grills.

This can be removed by wiping the unit with a damp

cloth.

3/19/10 2:46:52 PM