dicodes SBS18350Qi Podręcznik - Strona 5
Przeglądaj online lub pobierz pdf Podręcznik dla Elektroniczne papierosy dicodes SBS18350Qi. dicodes SBS18350Qi 18 stron.
Drukuj stronę05 Main Menu (Page 1)
Switching On/Off and Menu-Operation
The dicodes SBS18350-Qi is switched on by pressing the button shortly 5 times.
The display shows "Hello" and the user is led to the main menu. For
off the device there is menu item "Switch Off". When the value "0" is highlighted and
pressing the button, the mod displays "Bye.." and switches off shortly afterwards.
Important Note: The dicodes SBS18350-Qi differentiates between active switch off
and the automatic switch off after the selectable switch-off-time. When the mod was
switched off driven by the automatic timer, the device is switched on by pushing the
button "On Click" times.
"On Click" is a user selectable parameter. When "On Click" is set to 0 (zero), the device is immediately on
and by pressing the fire button longer than about 0.2seconds will let you vape immediately, even if the
mod was completely powered down.
After an active switch off, the device can only be switched on again by pushing the
button 5 times shortly. It is recommended to actively switch the device off during transport to avoid
unintended vaping or change of parameters (when the button is mechnically pressed without control).
The menu is entered by shortly pressing the button "MenuOn Click" times. By default, this user selectable
parameter is set to 3. By further pressing the button within a certain adjustable time (parameter Click Speed)
the user gets to the next menu item. If this certain time elapses without button actuation, the value of the
currently displayed parameter is inverted (highlighted) and can be modified then, by pressing the button
several times or by keeping the button pressed, which activates an auto-repeat operation.
When the button is not pressed any more, the display goes off and the parameter is permanently stored.
Vaping is activated, whenever the button is pressed for longer than about 0.2 seconds.
The maximum vape time is - dependent on the power setting - limited between 10 and 20 seconds. The
limitation is 10 seconds for power >40W and 20 seconds for power < 20W. In between it is linearily increased.
When the limit is reached, the error message "timeout", error 7 is diplayed. This error must be acknowledged
by waitin for the erro number being highlighted and then pressing the button shortly. "Err -" is displayed.
In the operation mode "Bypass" (mechanical mod), changing the power setting is not available, because the
power is defined by the battery voltage and coil resistance. The menu "Power" is not displayed in this case,
but the value display during and after the vape shows the actual power output to the coil.
With temperature controlled vaping activated, the power setting is the power limit for the temperature
regulator. If the power level is smaller than the value needed to achieve the selected temperature, the
operation changes from a temperature regulator to a temperature limiter. If the power level is sufficiently
high, it sets the heating up speed of the coil until the set-point temperature is reached.
When the battery voltage decreases, power is reduced starting from the voltage set by the parameter
Ubat,min (Extended Functions / Mod menu) plus 0.5V and ending at 10W at Ubat,min.
E.g. UbatMin=2.6V and Power=60W => Full 60W until battery voltage is at 3.1V, and then reduced to 50W
at 3.0V, 40W at 2.9V and so forth.
When the power is reduced, the battery symbol on the display will toggle with the message "Low" and
the reduced power level is shown. Furtehr information under chapter 06.
Using 18350 batteries, we recommend the settings for Ubat,min to 2.7V, otherwise 2.5V.
Changing the Power Setting
By means of menu item power-up and power-down, power can be adjusted between
5W and the power limit value, a user adjustable parameter in the extended functions/
heater menu. "Power Limit" provides a limitation for atomizers requiring low power or
limiting power depending on the battery size. We recommend to limit power to 20W
for 18350 batteries and to 30W using 18500 batteries. For 18650 batteries full power
of 60W might be released. Power can be changed in steps of 0.5W up to 30W and in
steps of 1W above 30W.
actively
switching