EPH Controls A27-HW Instrukcja obsługi

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Płyta główna EPH Controls A27-HW. EPH Controls A27-HW 2 stron. 2 zone programmer

Drukuj stronę
EPH Controls A27-HW Instrukcja obsługi
A27-HW - 2 Zone Programmer
Contents
1.
Factory default settings
2.
Factory program settings
3.
Resetting the programmer
4.
Setting the date and time
5.
ON/OFF period selection
6.
Adjusting the program settings
7.
Copy function
8.
Reviewing the program settings
9.
+1HR function
10. Advance function
11. Holiday mode
12. Backlight mode selection
13. Keypad lock and unlock
1. Factory default settings
Program:
5/2D
Backlight:
On
Keypad:
Unlocked
2. Factory program settings
P1 ON
P1 OFF
Mon-Fri
Sat-Sun
7:30
10:00
P1 ON
P1 OFF
Mon-Fri
Sat-Sun
Everyday
P1 ON
P1 OFF
3. Resetting the programmer
It is necessary to press the 'RESET' button prior to initial programming.
This button is located behind the cover on the front of the unit.
Press the 'RESET' button.
'rst No' appears on the screen.
Press '+' and Press 'OK' .
The programmer is now ready to be programmed.
4. Setting the date and time
Lower the cover on the front of the unit.
Move the selector switch to the CLOCK SET position.
Press the '
' or '
' buttons to select the day.
Press the '
' or '
' buttons to select the month.
Press the '
' or '
' buttons to select the year.
Press the '
' or '
' buttons to select the hour.
Press the '
' or '
' buttons to select the minute.
Press the '
' or '
' buttons to select 5/2D, 7D or 24H
The date, time and function are now set. Move the selector switch to the RUN
position to run the program, or to the PROG SET position to change the
program setting.
EPH Controls Ireland
[email protected] www.ephcontrols.com
Important: Keep this document
This 2 zone programmer is designed to
provide ON/OFF control for 2 zones.
5/2D
P2 ON
P2 OFF
P3 ON
P3 OFF
12:00
12:00
17:00
7D
P2 ON
P2 OFF
P3 ON
P3 OFF
24H
P2 ON
P2 OFF
P3 ON
P3 OFF
RUN
CLOCK
PROG
SET
SET
Press the 'OK' button.
Press the 'OK' button.
Press the 'OK' button.
Press the 'OK' button.
Press the 'OK' button.
Press the 'OK' button.
5. ON/OFF period selection
There are 4 modes available on this programmer for users to choose for their
individual application.
AUTO
The programmer operates 3 'ON/OFF' periods per day.
ALL DAY The programmer operates 1'ON/OFF' period per day.
This operates from the rst ON time to the third OFF time.
ON
The programmer is permanently on. **ON**
OFF
The programmer is permanently o . **OFF**
Lower the cover on the front of the unit. By pressing the 'HOT WATER SELECT'
23:00
button, you can change between AUTO / ALL DAY / ON / OFF for hot water.
Repeat this process for heating by pressing the 'HEATING SELECT' button.
6. Adjusting the program settings
Lower the cover on the front of the unit.
Move the selector switch to the PROG SET position.
You can now program the hot water.
Press the '
' or '
Press the '
' or '
Repeat this process to adjust the ON & OFF times for P2 & P3.
Press the 'Heating Select' button and repeat the above process to adjust for
HEATING.
When completed, move the selector switch to the RUN position.
7. Copy function
Copy function may only be used if the timeswitch is in the 7d mode.
Lower the cover on the front of the programmer.
Move the selector switch to the PROG SET position.
Set the ON & OFF times for the day of the week you wish to copy from.
Press the 'Holiday' button for 2 seconds.
The next day of the week will begin to ash.
Press the ' ' button to copy the ON & OFF times to this day.
Press the ' ' button to skip a day.
ON & OFF times can be copied to multiple days by using the ' ' button.
Press the 'OK' button when copying has been completed.
When completed, move the selector switch to the RUN position.
EPH Controls UK
[email protected] www.ephcontrols.co.uk
Page 1 of 2
Operating Instructions
CAUTION!
Before commencing, disconnect the
device from the mains. There are parts that
carry mains voltage behind the cover. Never
leave unsupervised when it is open. (Prevent
non specialists and especially children from
gaining access to it.)
Never remove this product from the
electrical baseplate. Disconnect from mains
supply in the event of any damage to any
buttons. Do not use sharp tools to push any
button.
' buttons to adjust the P1 ON time. Press the 'OK' button.
' buttons to adjust the P1 OFF time. Press the 'OK' button.
RUN
CLOCK
PROG
SET
SET
RUN
CLOCK
PROG
SET
SET
20221005_A27-HW_Opsins_PK