DieHard 200.71488 Instrukcja obsługi - Strona 6
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Zdalny rozrusznik DieHard 200.71488. DieHard 200.71488 11 stron. Jump starter/dc power source air compressor, inflator and ac power
Drukuj stronę
1. Attachthe corrugated hosewith
endadapter tothehigh-flow i nflator
outlet located directly a bove t he infla-
torON
/ OFF switch on the back of
the 1150.
2.
The main accessory nozzle attached
to the corrugated
hose accommo-
dates up to 4 sizes.
If another size
is needed an additional nozzle can
be attached to the end of the main
accessory nozzle.
3.
Insert the nozzle into the product to
be inflated.
4.
Push the inflator switch to the ON
position and inflate product.
5.
When product is inflated to the de-
sired level, push the inflator switch
to the OFF position and remove the
nozzle.
ESTIMATED
TIME
FOR
INFLATING*
24" Beach Ball
Pool Raft
Queen-size air mattress
2-Person Boat
1 to 3 minutes
4 to 6 minutes
4 to 8 minutes
8 to 10 minutes
*Times may vary depending on size and
product features.
USING
THE DEFLATOR
1.
Attach the corrugated
hose with the
end adapter to the high-flow deflator
outlet which is located on the right
side of the 1150.
2.
The main accessory nozzle attached
to the corrugated
hose accommo-
dates up to 4 sizes.
If another size
is needed an additional nozzle can
be attached to the end of the main
accessory nozzle.
3.
Insert the nozzle into the item to be
deflated.
4.
Push the inflator switch to the ON
position and deflate item.
5.
When product is deflated to the de-
sired level, push the inflator switch
to the OFF position and remove the
nozzle.
USING
THE BUILT-IN
LIGHT
1.
Position the 1150 on a flat, stable sur-
face near the intended work area.
2.
Push the Light/Display
switch to the
LIGHT position. The light will turn on
and illuminate your work area.
3.
Push the Light/Display switch to the
OFF position when work is completed.
4.
Chargethe
1150 as soon as possible
after using the built-in light.
NOTE: With a fully charged internal bat-
tery, the built-in light should provide 18
to 26 hours of continuous
useful light,
depending on ambient conditions.
BEFORE
USING
THE INVERTER
Important Safety Instructions:
• Keepthe 1150 inverterwell
ventilated in
order to properly disperse heat gener-
ated while it is in use. Make sure there
are several inches of clearance around
the top and sides and do not block the
vents on the back of the 1150.
• Make sure the 1150 is not close to any
potential source of flammable
fumes,
gases or clothing.
• Keep the 1150 dry.
• DO NOT allow the 1150 to come into
contact with rain or moisture.
• DO NOT operate the 1150 if you, the
1150, the device being operated or any
other surfaces that may come in contact
with any power source are wet. Water
and many other liquids can conduct
electricity,
which may lead to serious
injury.
• Do not place the 1150 on or near heat-
ing vents, radiators or other sources of
heat.
• Do not place the 1150 in direct sunlight.
The ideal air temperature
for operation
is between 50 ° and 80°F.
• Do not use inverter near open engine
compartment.
• Do not modify theAC receptacles in any
way.