DieHard Portable power 750 200.71486 Instrukcja obsługi - Strona 4
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Zdalny rozrusznik DieHard Portable power 750 200.71486. DieHard Portable power 750 200.71486 8 stron. Jump starter and dc power source
Drukuj stronę
WARNING:
Failure
to follow
instructions
may cause damage
or an explosion.
Read
entire instruction
manual
before
using this
product.
Always
shield
eyes
during
use
and wear safety
glasses.
JUMP-STARTING
A VEHICLE
ENGINE
Use in a well-ventilated
area. Keep hands,
hair,
clothing
and jewelry
clear
of fan
blades,
belts, pulleys
and other parts that
may cause
injury.
1.
Turn ignition
off before
making
cable
connections.
2.
Make
sure
the jump-start
ON/OFF
switch
is in the OFF position.
3.
Rest the 750 on a flat, stable surface
near
the vehicle
battery
and
away
from moving
engine
parts.
4.
Connect
the red clamp to the positive
terminal
of the vehicle
battery.
5.
Connect
the
black
clamp
to an
unpainted
and unmoving
part of the
vehicle
chassis
or engine
block.
CAUTION:
If you have connected
the
clamps
backwards,
an audio
alarm
will sound.
DO NOT turn the ON/OFF
switch
to the ON position.
This could
cause
serious
damage.
Reverse
the
connections
and the audio alarm
will
stop.
6.
Turn the ON/OFF
switch
to the ON
position.
7.
Turn the key and crank
the engine.
If the engine
does
not start,
wait at
least 3 minutes
before
attempting
to
crank the vehicle
again. This permits
the battery
to cool down.
8.
After the engine
starts, turn the jump-
start ON/OFF
switch
to OFF.
9.
Disconnect
the black clamp first and
then the red clamp.
Store the clamps
on the ears located
on the back of the
case.
10. Charge
the 750 as soon as possible
after jump-starting.
CAUTION:
To prevent
sparking
while the
750 jump-start
switch
is in the ON posi-
tion,
NEVER
allow
the clamps
to touch
together
or to contact
the same
piece of
metal.
And,
never
attempt
to charge
a
frozen
battery.
NOTE:
In the rare case
of jump-starting
a vehicle
that
has
a positive-grounded
vehicle
electrical
system,
connect
the
black
clamp
to the negative
terminal
of
the vehicle
battery.
Then
connect
the
red clamp
to an unpainted
and unmov-
ing part of the vehicle
chassis
or engine
block.
If you are unsure
of the nature
of
the vehicle's
electrical
grounding
system,
check
the owner's
manual
of the vehicle
or call the Customer
Technical
Assistance
number:
1-800-SEARS-64.
POWERING
A 12V
DC DEVICE
The Portable
Power 750 is a power source
for all 12 volt
DC accessories
that
are
equipped
with a 12V accessory
plug. The
DC accessory
outlet
has a 15-amp
auto-
matic overload
protection
circuit
breaker.
The breaker
will automatically
reset after
an overload
occurs.
To operate
a 12V DC device:
1.
Open the protective
cover
of the DC
power
outlet
on the left side of the
Portable
Power
750.
2.
Plug the 12V DC device
into the DC
power outlet,
and turn on the 12V DC
device
(if required).
3.
If the 12V DC device
draws more than
15A, the internal
circuit breaker
of the
Portable
Power
750 will momentarily
disconnect
power
to the device.
If
this occurs,
unplug
the device
and
the circuit
breaker
will automatically
reset after several
seconds.
4.
Charge
the Portable
Power
750 as
soon as possible
after each use.
Because
the DC power
outlet is internally
wired
directly
to the internal
battery,
ex-
tended
operation
of a 12V DC device
may
result
in excessive
battery
drain.