AXM AXB-SLD Skrócona instrukcja obsługi

Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla Kontroler AXM AXB-SLD. AXM AXB-SLD 2 stron. Slide interface

Drukuj stronę

ATTENTION: READ THIS FIRST!

For more detailed installation, configuration, programming, and operating

instructions, refer to the AXB-SLD Instruction Manual available on-line at

www.amx.com.

IMPORTANT SAFETY INSTRUCTIONS

When using your photographic equipment, basic safety precautions should

always be followed, including the following:

Read and understand all instructions before using.

Close supervision is necessary when any appliance is used by or near

children. Do not leave appliance unattended while in use.

Care must be taken as burns can occur from touching hot parts.

The appliance switch is provided with the symbols 0 indicating off and

1 indicating on. The symbols O and | may be used for this purpose.

Do not operate appliance with a damaged cord or if the appliance has

been dropped or damaged - until it has been examined by a qualified

serviceman.

Position the cord so that it will not be tripped over, pulled, or contact

hot surfaces.

If an extension cord is necessary, a cord with a current rating at least

equal to that of the appliance should be used. Cords rated for less

amperage that the appliance may overheat.

Always unplug appliance from electrical outlet before cleaning and

servicing and when not in use. Never yank cored to pull plug from

outlet. Grasp plug and pull to disconnect.

Let appliance cool completely before putting away. Loop cord loosely

around appliance when storing.

10. To reduce the risk of electric shock, do not immerse this appliance in

water or other liquids.

11. To reduce the risk of electric shock, do not disassemble this appliance,

but take it to a qualified serviceman when service or repair work is

required. Incorrect reassembly can cause electric shock when the

appliance is used subsequently.

12. The use of an accessory attachment not recommended by the

manufacturer may cause a risk of fire, electric shock, or injury to

persons.

13. Connect this appliance to a grounded outlet.

14. Disconnect this unit from its source of supply before replacing the

projection lamp.

15. This appliance has a polarized plug (one blade is wider than the

other). To reduce the risk of electric shock, this plug is intended to plug

into a polarized outlet only one way. If the plug does not fit fully into the

outlet, reverse the plug. If it still does not fit, contact a qualified

electrician. Do not modify the plug in any way.

SAVE THESE INSTRUCTIONS

Wiring Requirements

Caution: Do not connect power to the AXB-SLD until the wiring is

complete. If you are using a 12 VDC power supply, apply power to the

AXB-SLD only after installation is complete.

The AXB-SLD requires 12 VDC power to operate properly and uses a 4-pin

AXlink cable for power and data. The power can be supplied by the AMX

system's AXlink cable or with an optional 12 VDC power supply. The

maximum wiring distance between the control system and AXB-SLD is

determined by power consumption, supplied voltage, and the wire gauge

used for the cable. The following table lists wire sizes and the maximum

lengths allowable between the AXB-SLD and control system. The maximum

wiring lengths for using AXlink power are based on a minimum of 13.5 volts

available at the control system's power supply.

Wiring Guidelines at 120 mA

Wire Size

Maximum Wiring Length

18 AWG

978.09 feet (298.12 m)

20 AWG

618.81 feet (188.61 m)

22 AWG

385.80 feet (117.59 m)

24 AWG

243.19 feet (74.12 m)

If the AXB-SLD is installed farther away from the control system than

recommended in the Wiring Guidelines table, connect a 12 VDC power

supply to the 2-pin 12 VDC PWR connector on the rear panel.

Product Information

The AXB-SLD Slide Interface unit provides AXlink slide projector control for

power, forward, reverse, and focus for any EC3-compatible projector. The

AXB-SLD is the ideal way to control a slide projector in an Axcess

environment. The AXB-SLD provides a switched-power receptacle for up to

1,200 watts along with a standard Kodak 5-pin projector control cable.

Compatibility with the Axcess Central Controller is achieved through a 4-pin

AXlink bus connector. The front panel LEDs indicate the status of all

functions.

AXB-SLD Slide Interface

Compatible Projectors

All EC-3 compatible projectors

Interface Power

120 mA @ 12VDC

Projector Power

1,200 watts, 10 amp maximum, 50/60 Hz

Unit Power

3 watts maximum

Fuse Rating

10 amp internal

Front Panel Components:

AXlink status LED

The green AXlink LED blinks to indicate AXlink communication

activity, power, and data status:

One blink per second indicates power is active and AXlink

communication is functioning properly.

Full-on indicates that there is no AXlink control or activity, but power

is on.

DEVICE DIP switch

The 8-position DIP switch on the front panel is used to set the

device number for use with the Central Controller. The device code

identifies the AXB-SLD unit as one of the devices connected to the

AXlink bus. See the Installation section for specific information

about setting the device number.

PWR button

The PWR pushbutton is the AXB-SLD power on/off switch. This

pushbutton controls the switched line power to the projector. A red

LED in the switch is illuminated when projector power is on.

Slide Interface LEDs

FWD LED: lights when the AXB-SLD sends forward commands to

the projector.

REV LED: lights when the AXB-SLD sends reverse commands to

the projector.

FOC LEDs: light when the AXB-SLD sends focus in/out commands

to the projector.

Rear Panel Components:

AXlink connector

The AXlink connector is a 4-pin captive-wire connector for AXlink

data and power. Terminals accept 24 - 12 AWG wire.

Projector Control cable

A ten-foot long, 5-pin EC3-compatible EBY projector control cable

(US Kodak style).

Switched Power outlet

A 110 VAC (up to 1,200 watts) switched power outlet controls power

to the projector using the front panel PWR switch or from AXlink

control. Projector power can be switched from the AXB-SLD front

panel, even if AXlink communication is not on. The switched power

connector is a standard 3-prong AC receptacle.

AC Power Cord

A 110 VAC (50/60Hz) three-wire standard power cord provides AC

power to the AXB-SLD.

Dimensions (HWD)

1.5" x 5.5" x 5.5" (38.1 mm x 139.7 mm x 139.7 mm)

Weight

26 oz (737.08 g)

Options

AC-RK Accessory Rack Kit

Quick Start Guide

AXB-SLD