Cinepro 4K6 MK-4 SE-Gold Instrukcja obsługi - Strona 4
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Wzmacniacz Cinepro 4K6 MK-4 SE-Gold. Cinepro 4K6 MK-4 SE-Gold 9 stron. High resolution - extended dynamic six channel theater amplifier
Drukuj stronęREAR PANEL CONNECTIONS - INPUT
FRONT INPUTS
CENTER/
SUR-EFX
INPUTS
REAR INPUTS
GROUND LIFT switch
(Set for lowest hum
level in speakers)
INPUTS
Hook the signal cords from your processor to the respective inputs on the Cinepro 4K6 MK-4 SE-Gold. Note that all inputs are
marked with the logical speaker positions - Front Left/Ch. 1, Front Right/Ch. 2, Center/Ch. 3, etc. These correspond to the front
panel markings and the speaker output jacks. Use good quality connecting cords. For normal operation, ensure that each of the
three mode switches is set to DUAL. For Mono operation, see below.
Balanced
Use XLR type male plug and insert into gold plated XLR jacks. Pin 1-GND, Pin 2-Hi, Pin 3-Lo.
Set switch below jacks to BAL/XLR
Unbalanced
Use RCA type male plug and insert into gold plated RCA jack on back panel.
Set switch below jacks to UN-BAL/RCA.
Most home processors utilize unbalanced RCA type cable for signal connection. Some high end processors use balanced type
connections. Use the input appropriate to your processor.
INPUT - CENTER CHANNEL/BRIDGED MONO MODE (FOR EXAMPLE)
In the event that you are not using the rear surround/subwoofer channel, or have a powered subwoofer, the Cinepro 4K6 MK-4
SE-Gold can combine two channels of amplifi cation (center and woofer channels) into one single channel of prodigious power
output. The bridged speaker must be a minimum of 4 ohms or greater.
1. Connect either the balanced or the unbalanced input cord (one only—remember this is mono) to the center/channel 3
input. Leave the SUR-EFX/chennel 4 input unconnected.
2. Hook the center channel speaker to the RED posts as indicated on the speaker output plate. The top RED post (center
channel) is the (+) connection, and the bottom RED post (subwoofer) is the (-) connection.
3. Switch the mode switch on this two channel group to MONO. You now have a very dynamic center channel amplifi er
(over 1,200 watts available).
GROUND LIFT SWITCH
After hookup, if any hum is present in the speakers, fl ip the ground lift switch (located at the bottom of the input panel) to LIFT.
One of the two positions should have lower hum than the other. Do this test with no signal, but with AC power applied to the
amplifi er. Experiment to fi nd the quietest position.
In certain systems, especially those with more than one three-prong power corded component, low level hum may still be
present. Under these conditions, it is advisable to use a three-to-two-prong adapter (available at local hardware stores) to isolate
the system to just one grounded chassis. It is best to have the preamp/receiver operate with the three-prong grounded plug, or
if the preamp just has a two-prong power plug, leave the Cinepro 4K6 MK-4 SE-Gold as your only "grounded" component. Be
sure to check the other component's manuals to see if it is safe to operate the equipment in the ungrounded mode.
DUAL OR MONO Bridging switch
(usually set to DUAL, unless mono
operation is desired)
UNBALANCED RCA input jack
BALANCED XLR
BALANCED XLR input jack
BALANCED XLR input jack
BAL / UN-BAL switch
SET TO UN -BAL IF USING RCA INPUT JACKS.
SET TO BAL IF USING XLR INPUT JACKS.
(Note: each pair of inputs must be set separately.)
12v DC REMOTE TURN-ON
4