AXTON A594DSP Instrukcja instalacji i obsługi - Strona 4

Przeglądaj online lub pobierz pdf Instrukcja instalacji i obsługi dla Wzmacniacz samochodowy AXTON A594DSP. AXTON A594DSP 17 stron. 4 channel class d car amplifier

Drukuj stronę
CONNECTIONS + CONTROLS A594DSP
1 2
3 4 5
6
7
8
9
bl
bm
bn bo
1* In some cases with old headunits the Auto-Turn-On function cannot work. If you meet this problem, please connect the
"ACC-IN" to the ACC/Amp Remote of the car stereo or another cable which will provide +12 V only when the car stereo
is turned on. Secondly select "REMOTE TURN ON" on the remote switch (12).
2* REM-Out: Connect this wire to the remote input of a separate amplifier, for example a mono amp for a subwoofer.
REMOTE CONTROL
1
Connect the optional RC for convenient operating of Master Volume, Bass Volume and Mute
function.
When you are using the ABT50 with OTG for iPhone for lossless audio transmission, the
signal is sent directly avoiding any converter. That's awesome. But it also means that you
are not able to adjust the volume with your iPhone. Therefore you need to connect the
separate available RC.
ANTENNA
2
External Bluetooth antenna for data and audio streaming.
POWER TERMINAL
3
Connect Ground and Battery cables when additional power is necessary or desired.
FUSE
4
If the fuse is broken, replace it with a new fuse of same value.
OPTICAL OUTPUT CH9/CH10
5
To send the signals of CH9 and CH10 to another Axton DSP amplifier with optical input.
COAXIAL
6
This input provides power for the ABT50 and also receives audio data from this device. It's
impossible to connect usual USB sticks.
SERVICE
7
For internal use only.
SPEAKER
1*
ACC-in
11
GND
2*
Rem-out
12
+B
3
RR-in
13
FL+out
4
RR+in
14
FL-out
5
RL-in
15
FR+out
6
RL+in
16
FR-out
7
FL-in
17
RL+out
FL+in
RL-out
8
18
FR-in
RR+out
9
19
FR+in
RR-out
10
20
– 6 –
LINE OUT
8
If you only want to use the DSP function of the A594DSP with a separate high performance
amplifier, connect the line out of the A594DSP with the RCA input of your amplifier.
SPEAKER LEVEL INPUT/OUTPUT
9
This is the main connector for Plug & Play installation.
OPTICAL INPUT
bl
a) Connect to ABT50 for lossless Hi-Res audio transmission from your smartphone.
20
b) Connect another Axton DSP amplifier with optical output.
SPEAKER IMPEDANCE
bm
Choose according to the connected speakers. If your system is equipped with 3 Ohm
speakers or less, switch to 2 ohm. Minimum load is 2 Ohm.
REMOTE / SIGNAL TURN ON
bn
Choose if the amp shall turn on by separate ACC+/Remote wire or by DC Offset signal.
POWER
bo
Two color LED: Green light shows normal operation. Green light blinking shows a current
data transfer, i.e. receiving data from the app. Red light shows protection mode, i.e. too low
impedance.
A594DSP MOUNTING INSTRUCTIONS
1. Before you start with the installation, make sure you know the security code of your
headunit (if applicable).
2. Remove the headunit from the dashboard and disconnect the main wire harness.
3. Find a place for the A594DSP and connect the optionally available car-specific wire harness
to the amp.
4. Optionally: For more power output please follow these steps: Run a 6 mm
the (+) pole of the battery to the (BATT) terminal of the amplifier. Use a fuse with the related
value of the cross section of the power wire. The distance between the B+ pole and the fuse
holder must be 30 cm or less. Run the minus cable with the same cross section from the
(GND) terminal of the amp to the vehicle chassis ground. Make sure that the contact surface
is clean in order to get best conductance.
5. Optionally: For Hi-Res Sound from your smartphone: Connect the optical and coaxial cables
to the inputs of A594DSP and outputs of the AXTON ABT50. Connect your smartphone via
Bluetooth to the ABT50 for using APTX-HD standard or use the AXTON OTG cable for
absolutely lossless audio transmission: the signal is sent from your smartphone directly to the
amplifier without passing any D/A converter.
6. Optionally: Connect the remote control for convenient operation of the Master Volume, Bass
Extender and Mute function. Recommended when using A594DSP without any headunit.
7. Connect the wire to the headunit.
8. Install the headunit back in the dashboard.
Stand-alone installation
When you intend to use the A594DSP without any headunit, please connect the optionally
available N-A480DSP-ISOFLX cable and connect the wires according to the wiring diagram.
Switch (12) is to be set to "Remote turn on".
power wire from
2
– 7 –