Circa Enterprises Inc. 2100BN-6 Procedura instalacji

Przeglądaj online lub pobierz pdf Procedura instalacji dla Terminale dotykowe Circa Enterprises Inc. 2100BN-6. Circa Enterprises Inc. 2100BN-6 2 stron. 2100 series, building entrance terminal

Drukuj stronę

3.0

Fuse Link Specifications:

The Terminal unit is equipped with a built in fuse link. If an

overcurrent condition were to occur, the chassis will act as a

fuse chamber, greatly reducing any threat to safety. Once

fuse links have been fused, they cannot be rehabilitated or

repaired.

4.0

Installation Data:

The Terminal should be installed to the network's standard

installation procedure. However, the following factors should

be considered.

4.1

Use care when unpacking the Terminal from its shipping

carton to avoid damage to the Terminal, modules, or

connectors.

4.2

Install the Terminal as close to the incoming entrance cable as

possible.

4.3

The Terminal can be mounted on any level, uniform vertical

surface.

4.4

Install the Terminal where it will be accessible to technicians at

all times without the terminal obstructing individuals or

equipment.

Note: Although the Terminal is designed to withstand extreme

conditions, it is always best to avoid any unnecessary

problems by observing the following important notes: When

installing the Terminal, it is highly recommended that unit be

placed in a non-combustible area. (The environment

surrounding these devices should not contain flammable

materials such as curtains, carpeting, etc.)

If the installation for the telco equipment is not in an assigned

electrical room, it is advised to avoid areas with dust, moisture,

extreme environmental conditions, heavy traffic areas requiring

rolling machinery, pipes used to transport water, fuel, and

gases.

4.5

Avoid exposing the Terminal to chemicals or cleaning liquids,

which could damage various plastic components within the

device.

5.0

Installation Procedures:

Mount the Terminal to a surface using the supplied mounting

screws or approved network standards screws.

5.1

Outside Plant Termination (Incoming/ QCBIX®):

To terminate the entrance cable pairs to the incoming QCBIX®

connector, the procedure is as follows: Refer to figure 1 for

QCBIX® connector arrangements. The pairs should then be

jumpered to the QCBIX® connector using a QTBIX16A

termination tool.Caution: Do not use a screwdriver for

attaching line pairs to QCBIX® terminals, as a screwdriver

may spread the clip beams and result in a faulty connection.

5.2

Distribution Termination (Outgoing/ QCBIX®):

The procedure for terminating the distribution cable pairs onto

the outgoing QCBIX® connector is the same as indicated in

5.1, except the cable pairs are routed to the "OUT" terminal.

6.0

Grounding:

A #6 AWG wire should be connected from the Terminal ground

lug to a local ground as per network standard methods. It

should be noted that incorrect bonding, grounding or standards

would result in terminal and protection module failure.

7.0

Terminal Module Installation:

If the Terminal is purchased with the terminal modules

installed they will be inserted in the terminal panel in the detent

position. A distinctive "notch" in the three long pins of the

module indicates the detent position. This will connect the

incoming tip / ring as well as grounding circuits of the module.

Note: When the module is in detent position it will protect

only the incoming (outside plant) cable. The module must

be fully inserted to provide protection to both the central

office and customer premise side of the installation.

7.1

After all incoming and outgoing connections are completed;

fully insert the terminal module until the base of the module

meets the terminal block. This will connect the distribution

termination (Outgoing/ QCBIX®) side of the unit to the outside

plant (Incoming/ QCBIX®) side of the unit.

7.2

Fully test all connections.

8.0

Terminal Diagram:

OUT

2406B-6

3.9

5.0

Important Note:

All statements, technical information and recommendations related to the

Seller's products are based on information believed to be reliable, but the

accuracy or completeness thereof is not guaranteed. Before utilizing the

product, the user should determine the suitability of the product for its intended

use. The user assumes all risks and liability whatsoever in connection with

such use. Any statements or recommendations of the Seller, which are not

contained in the Seller's current publications, shall have no force or effect

unless contained in an agreement signed by an authorized officer of the Seller.

The statements contained herein are made in lieu of all warranties, express or

implied, including but not limited to the implied warranties of merchantability

and fitness for a particular purpose which warranties are hereby expressly

disclaimed.

Seller shall not be liable to the user or any person under any legal theory,

including but not limited to negligence or strict liability, for any injury or any

direct or consequential damages sustained or incurred by reason of the use of

any of the Seller's product that were defective.

6.45