FHC CAROLINA CLNAS2 Skrócona instrukcja obsługi

Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla Stojaki i stojaki FHC CAROLINA CLNAS2. FHC CAROLINA CLNAS2 3 stron. Wall mount hinge - short back plate

Drukuj stronę
SHOWER HINGE TEMPLATE
CAROLINA
Wall Mount Hinge - Short Back Plate
ITEM NO. CLNS2
ITEM NO. CLNAS2 (Adjustable)
SPECIFICATIONS
SPECIFICATIONS
Glass Sizes:
3/8" to 1/2" (10 mm to12 mm) Tempered Glass Only
Construction:
Solid Brass with HD Stainless Steel Back Plate
Closing Type:
Self-Centering When Within 15 Degrees of Closed Position
Cutout Required:
See Page 2
Includes:
Hinge body, glazing gaskets, wall mounting screws, allen
head/phillips head cover plate screws, and fabrication template.
Use:
Residential Bath and Commercial Hotel Applications
GASKET SPECIFICATIONS:
For 3/8" (10mm) Glass: Use One Thick Gasket On Each Side
For 1/2" (12mm) Glass: Use One Thin Gasket On Each Side
GLASS INSTRUCTIONS:
Only use tempered safety glass. To prevent damage to the hinge finish
during installation, do not use power tools when installing these hinges.
IMPORTANT INFORMATION:
The Carolina Series Hinge has a dual degree pivot pin. It comes factory set
at 90 degrees for normal door closing applications. There is also a secondary
setting on the hinge pivot pin that can be field adjusted to allow an additional
5 degrees of closing for jobs that require a firmer positive position against a
jamb or seal
3/8" (10 mm) GLASS
Approx. 5 lb/ft
MAXIMUM DOOR
CAPACITY
DOOR WEIGHT
USING 2 HINGES
110 LBS. (50 kg)
USING 3 HINGES
140 LBS. (64 kg)
NOTE: Do not exceed either maximum weight or width when choosing proper quantity of hinges.
FRAMELESS HARDWARE COMPANY
1/2" (12 mm) GLASS
Approx. 6.4 lb/ft
2
2
DOOR WIDTH
36" (813 mm)
36" (914 mm)
P.O. Box 1906, South Gate, CA 90280
2-3/16"
(56 mm)
2-3/4"
(70 mm)
2-5/16"
(59 mm)
CARE & CLEANING GUIDELINES:
For best results, keep the following recommendations in mind when caring for your FHC shower door hardware.
Your shower door should be dried daily with a soft towel or cloth to ensure its original finish. Do not use harsh
cleaners or chemicals on the hardware, as many of the components are coated with a clear lacquer that will
become damaged beyond repair. Always test your cleaning solution in an inconspicuous area prior to cleaning
the entire hardware surface. Wipe surfaces clean using a soft, dampened cloth or sponge, and rinse completely
with warm water immediately after applying the cleaning solution. Use only small amounts of liquid, gentle,
cleaner. Never use abrasive products, sponges, or wire scrub brushes while cleaning hardware.
MAINTENANCE:
FHC's hinges come factory greased for a silent, hassle-free experience.
If there is any noticeable squeaking that occurs after installation, it is recommended
to apply a few drops of (3 in 1) multi-purpose oil to the hinge, at the nylon washer/pivot
location. The lubricant will penetrate the hinge crevices, reducing friction, cleaning
grime, and/or buildup. Spray lubricants are prohibited. If, for some reason, the hinge
is disassembled during maintenance, use a small amount of white lithium grease
to lubricate the interior hinge components.
Toll Free: (888) 295-4531 | Fax: (323) 336-8307 | Web: fhc-usa.com
PROFESSIONAL GRADE
36"
36"
MAX
MAX
WIDTH
WIDTH
2-HINGES
2-HINGES
MAX
110
LBS
3-15/16"
SEE TEMPLATE ON BACK
SEE TEMPLATE ON BACK
(100 mm)
Refer to Dimensions Shown
Refer to Dimensions Shown
to Ensure Accuracy
to Ensure Accuracy
7/16"
(11 mm)
EXPERIENCE AND INNOVATION
36"
36"
MAX
MAX
WIDTH
WIDTH
3-HINGES
3-HINGES
MAX
140
LBS
LIT0004L 0.17.22 PG 1 OF 3