FHC GLENDALE Podręcznik

Przeglądaj online lub pobierz pdf Podręcznik dla Stojaki i stojaki FHC GLENDALE. FHC GLENDALE 2 stron. Wall mount hinge - full back plate

Drukuj stronę
SHOWER HINGE TEMPLATE
GLENDALE
Wall Mount Hinge - Full Back Plate
ITEM NO. GLENF1
SPECIFICATIONS
SPECIFICATIONS
Glass Sizes:
3/8" to 1/2" (10 mm to 12 mm) Tempered Glass Only
Construction:
Solid Brass with HD Stainless Steel Back Plate
Closing Type:
Self-Centering When Within 15 Degrees of Closed Position
Cutout Required:
Cutout No. SD1
Includes:
Hinge body, glazing gaskets, wall mounting screws, allen
head/phillips head cover plate screws, and fabrication template.
Use:
Residential Bath and Commercial Hotel Applications
GASKET SPECIFICATIONS:
For 3/8" (10mm) Glass: Use One Thick Gasket On Each Side
For 1/2" (12mm) Glass: Use One Thin Gasket On Each Side
GLASS INSTRUCTIONS:
Only use tempered safety glass. To prevent damage to the hinge finish
during installation, do not use power tools when installing these hinges.
IMPORTANT INFORMATION:
The Glendale Series Hinge has a dual degree pivot pin. It comes factory set
at 90 degrees for normal door closing applications. There is also a secondary
setting on the hinge pivot pin that can be field adjusted to allow an additional
5 degrees of closing for jobs that require a firmer positive position against a
jamb or seal.
3/8" (10 mm) GLASS
Approx. 5 lb/ft
2
MAXIMUM DOOR
CAPACITY
DOOR WEIGHT
USING 2 HINGES
80 LBS. (36 kg)
USING 3 HINGES
120 LBS. (54 kg)
NOTE: Do not exceed either maximum weight or width when choosing proper quantity of hinges.
FRAMELESS HARDWARE COMPANY
CARE & CLEANING GUIDELINES:
For best results, keep the following recommendations in mind when caring for your FHC shower door hardware.
Your shower door should be dried daily with a soft towel or cloth to ensure its original finish. Do not use harsh
cleaners or chemicals on the hardware, as many of the components are coated with a clear lacquer that will
become damaged beyond repair. Always test your cleaning solution in an inconspicuous area prior to cleaning
the entire hardware surface. Wipe surfaces clean using a soft, dampened cloth or sponge, and rinse completely
with warm water immediately after applying the cleaning solution. Use only small amounts of liquid, gentle,
cleaner. Never use abrasive products, sponges, or wire scrub brushes while cleaning hardware.
GLEN037 Glendale Wall Mount Hinge - Full Back Plate
MAINTENANCE:
1/2" (12 mm) GLASS
FHC's hinges come factory greased for a silent, hassle-free experience.
Approx. 6.4 lb/ft
2
If there is any noticeable squeaking that occurs after installation, it is recommended
DOOR WIDTH
to apply a few drops of (3 in 1) multi-purpose oil to the hinge, at the nylon washer/pivot
location. The lubricant will penetrate the hinge crevices, reducing friction, cleaning
28" (711 mm)
grime, and/or buildup. Spray lubricants are prohibited. If, for some reason, the hinge
is disassembled during maintenance, use a small amount of white lithium grease
32" (813 mm)
to lubricate the interior hinge components.
P.O. Box 1906, South Gate, CA 90280
2"
50 mm)
3-1/2"
(89 mm)
2-3/16"
(56 mm)
Toll Free: (888) 295-4531 | Fax: (323) 336-8307 | Web: fhc-usa.com
PROFESSIONAL GRADE
28"
28"
MAX
MAX
WIDTH
WIDTH
2-HINGES
2-HINGES
MAX
MAX
80
80
3-1/2"
LBS
LBS
(89 mm)
SEE TEMPLATE ON BACK
SEE TEMPLATE ON BACK
Refer to Dimensions Shown
Refer to Dimensions Shown
to Ensure Accuracy
to Ensure Accuracy
7/16"
(11 mm)
EXPERIENCE AND INNOVATION
LIT0001A REV. 07.25.22 PG 1 OF 2
32"
32"
MAX
MAX
WIDTH
WIDTH
3-HINGES
3-HINGES
MAX
MAX
120
120
LBS
LBS