Crelling Harness 28 Podręcznik - Strona 2

Przeglądaj online lub pobierz pdf Podręcznik dla Akcesoria samochodowe Crelling Harness 28. Crelling Harness 28 2 stron.

Drukuj stronę
Model 28 Fitting Instructions
1.
If fitting a brand new harness, remove any Rubber Bands & unfasten the two Vertical Fixing Straps [a].
2.
Holding the two Aluminium Bar Buckles
[b]
harness against the front of the seat back & place the Fixing Straps up & over the seat back.
[d] Shoulder Strap
[e] Waist Belt Buckle
[f] Understrap
3.
Pass the tail-ends of the two lower sections
of the Vertical Fixing Straps
[a]
(on either side
of the understrap [f]), down through the gap
between the seat back & seat cushion.
Nb. The Understrap should remain lying on
the seat cushion.
6.
Position the Understrap
[f]
centrally on the seat cushion
7.
If the passenger is under 135cm place a Booster Seat or Cushion on top of the Understap to comply with child seat safety
legislation
(See back of Instructions for further information)
8.
Position the Back Pad & Body Harness on the seat so that the waist belt will be in line with the waist when the passenger sits down.
9.
With the harness unfastened at the waist belt sit the passenger on the understrap / child seat in the most upright position as
possible & bring their arms through the shoulder straps [d].
8.
Now bring the understrap
[f]
up between the legs and loop it back onto the waist belt over the buckle [h].
9.
Connect the waist belt buckle to fasten the harness. Position the buckle centrally at waist level on the passenger.
10.
Adjust all straps to fit tightly yet comfortably by pulling the tail-ends of strapping through the Adjuster Buckles [i].
11.
If using the Houdini Stop Chest Strap [j], attach to Shoulder Straps underneath the Adjuster Buckles [j].
12.
Ensure that the three Comfort Pads
[g]
are in position over the Adjuster Buckles
13.
Fasten the vehicle safety belt over the top of the Model 28 Harness.
14.
To remove the passenger from the harness - Unfasten the buckle on the waist belt at the centre-front.
40mm Adjuster Buckle
[g]
[i]
[j]
[h]
(attached to the upper section of the Vertical Fixing Straps) place the back pad of the
4.
Now feed the tail-ends of the Fixing straps up through the Aluminium Bar
Buckles
(see diagram [b])
& pull down to tighten around the seat back as
securely as possible.
5.
Each tail end should then be passed through the Sliplock Slide
prevent the Fixing Straps from loosening during transit.
[i]
on the Shoulder & Under Straps.
To Extend Straps
The 40mm Adjuster is slightly spring loaded
to lock the webbing into position.
To release the webbing you need to squeeze
the Adjuster whilst pulling on the lower
webbing strap.
Squeeze Adjuster
to release
webbing
50mm Aluminium Bar Buckle
[a] Vertical Fixing Strap
Sliplock Slide
[b] 50mm Aluminium
Bar Buckle
[c] 50mm Sliplok slide
Steel Safety Buckle
This buckle has proven extremely successful when fitted to our
[c]
to
harnesses as an alternative to the standard 'quick release' buckle.
It helps prevent those passengers with inquisitive fingers,
challenging behaviour or learning difficulties from releasing the
harness buckle.
The buckle operates in reverse to the standard vehicle buckles as
it is opened by raising a spring loaded lever or over-catch and will
not press release. The spring loaded over-catch locks the buckle
when assembled and prevents accidental opening.
See instruction
provided.
Emergency Seat Belt Cutter
To Tighten Straps
We strongly recommend that a seat belt cutter is kept in the vehicle
as a safety precaution for those harnesses fitted with a Steel Safety Buckle.
Simply pull the tail-end of
the webbing strap.
A simple but effective device for ensuring the occupants of a car are able
to exit quickly and safely, particularly in the overturned car.
The Adjuster will lock the
webbing into position
It is perfectly safe as the blade is encased.
Cat. Ref: SK
Comfort Sleeves
Velcro Comfort Sleeves will be supplied with each harness.
These can be fitted around the shoulder Straps & under strap where required.
There is a knurled sliding bar for adjustment designed to
prevent webbing slip.
The buckle is made from Type 316 Stainless Steel and Nylon
6 and is assembled with tamper proof screws.
The 40mm buckle has a Breaking Strain of 630 kg
We recommend that the buckle instructions provided with each
harness are displayed in a prominent position in the
vehicle - to instruct the carer how to release the buckle mechanism
in the event of an accident.
(Optional Extra)
Webbing is threaded
through the sliding
bar buckle
Loose ends of webbing
are often passed back
through these slides to
prevent slippage & to
prevent the Fixing Straps
from loosening during
transit.