Cres Cor ROAST-N-HOLD CO-151-HUA-6B Specyfikacje - Strona 2
Przeglądaj online lub pobierz pdf Specyfikacje dla Piekarnik konwekcyjny Cres Cor ROAST-N-HOLD CO-151-HUA-6B. Cres Cor ROAST-N-HOLD CO-151-HUA-6B 2 stron. Cres cor aquatemp humidity convection and retherm ovens
Również dla Cres Cor ROAST-N-HOLD CO-151-HUA-6B: Instrukcja obsługi i konserwacji (10 strony), Instrukcja instalacji, obsługi i konserwacji (13 strony)
Drukuj stronęDETAIL OF
PAN SLIDE
CRES COR
PAN
MODEL NO.
CAP/ANGLES
6
CO-151-HUA-6B
SETS
Note: Refer to pan size chart at end of section.
ALL CONSTRUCTION IS RIVETED, WELDED AND FINISHED.
CABINET:
• Body: 22 ga. 304 stainless steel.
• Reinforcement: Internal framework of 16 ga. stainless steel.
• Insulation: Fiberglass, thermal conductivity (K factor) is .23 at 75˚F.
•
1-1/2" in back wall, door, base; 2" in side walls.
• Air tunnel: 20 ga. stainless steel, lift-out type; mounted
•
on rear wall.
• Work Top: 18 ga., 304 stainless steel.
BASE:
• One piece construction, .125 aluminum.
• Casters: 5" dia., swivel, modulus tires, 1-1/4 wide, load cap.
•
250 lbs. each, temp. range -45˚/+180˚F. Delrin bearings. Front
casters equipped with brakes.
DOOR:
• Field reversible.
• Formed 22 ga. 304 stainless steel.
• Latch: Chrome plated steel, high temperature ceramic
•
magnetic type; mounted inboard.
• Hinges: Heavy duty chrome plated steel, lift-off type; mounted
•
inboard.
• Gasket: Perimeter type, silicone.
• Pan stops: Embossed.
PAN SLIDES:
• Wire angles (.306 dia.), nickel chrome plated; mounted on
lift-out posts.
• (6) sets of angles adjustable on 1-1/2" centers.
• Grids (3): Nickel chrome plated steel, raised wire 17" x 25".
POWER REQUIREMENTS AVAILABLE:
• 4700 Watts, 208 Volts, 60 Hz., 1 phase, 24 Amps.,
•
30 Amp. service.
• 4700 Watts, 240 Volts, 60 Hz., 1 phase, 20 Amps.,
•
30 Amp. service.
• 4700 Watts, 208 Volts, 60 Hz., 3 phase, 13 Amps.,
•
20 Amp. service.
• 4700 Watts, 240 Volts, 60 Hz., 3 phase, 12 Amps.,
•
20 Amp. service.
5925 Heisley Road • Mentor, OH 44060-1833
Phone: 877/CRESCOR • Fax: 440/350-7267
www.crescor.com
© Crescent Metal Products, Inc. 2002 All rights reserved
DIM "A"
SIZE
WIDTH
SEE NOTE
IN
28-3/4
BELOW
MM
740
®
DIM "B"
DIM "C"
DEPTH
HEIGHT
WIDTH
37-3/4
43-3/4
21-1/4
960
1115
540
POWER UNIT COMPONENTS:
• Body: Formed 20 ga. 304 stainless steel with black control
•
panel, recessed and tilted 7˚.
A) Thermostat (holding): Solid state, room ambient to 250˚F. (121˚C.).
B) Thermostat (cook/retherm): Solid state, room ambient to 350˚F.
B)
(176.5˚C.).
C) Pilot lights (2).
D) Switch: Lighted ON-OFF rocker type.
E) Timer: 24 hr. digital countdown; infinite memory retention.
F) Thermometer.
• Power cord: Permanent, 6 ft., 10/3 ga. with right angle plug.
• Heaters (3): 1470 Watts each.
• Blower motors (3).
• Vent fans (2).
• Fuses (2): 3 Amp.
INSTALLATION REQUIREMENTS:
• Check local vent hood codes for mobile Roast-N-Hold ovens.
SHORT FORM SPECIFICATIONS
Cres Cor Roast-N-Hold Half Size Convection Oven
Model CO-151-HUA-6B. Removable power unit 20 ga.
304 stainless steel, recessed control panel. Cabinet and
door 22 ga. 304 stainless steel; stainless steel internal
frame; coved corner interior. Fiberglass insulation in
sides 2"; back, door and base 1-1/2". High temperature
magnetic latch. (6) sets universal angles for multiple
pan sizes and spacing. One piece base .125 aluminum.
5" swivel modulus casters, Delrin bearings. Load
capacity 250 lbs. each. 4700 Watts,
60 Hz.,
the following accessories:
UL Sanitation, UL, CUL listed.
In line with its policy to continually improve its products,
CRES COR reserves the right to change materials and
specifications without notice.
CO-151-HUA-6B
6-30P
INSIDE DIMENSIONS
DEPTH
HEIGHT
26-1/2
28
675
715
(refer to above drawing)
Phase. 2 year parts warranty. Provide
_
L15-20P
WEIGHT
ACT.
LBS
296
KG
134
Volts,
.
Litho in U.S.A.