Digimerge DPD24DL Instrukcja obsługi - Strona 6
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Kamera IP Digimerge DPD24DL. Digimerge DPD24DL 14 stron. Ultra resolution day & night ir dome camera
Również dla Digimerge DPD24DL: Instrukcja obsługi (14 strony)
Drukuj stronę
INSTALLATION. VANDAL DOME
ATTENTION - If using DC power, follow the correct
1
polarity as marked on the power cable.
1) Loosen the three tamper screws using the provided
Note: If you plan to use conduit fitting, remove conduit
Method 1 - Direct Attach Install
2
2a) Use the included mounting template (Installation
a
Remove the 3rd base locking screw and install the 3rd
Go to step
OR
Method 2 - Camera Base Install
2b) Use the included mounting template (Installation
b
Method 3 - Junction Box Install
2c)
3
a
3a) Reinsert camera module into camera base by
b
3b) Use the 3 base locking screws to secure
Go to step
allen key. Lift the dome cover.
cap using the provided conduit key.
A
B
In
stallation Option 1:
Use holes marked with 'A' when
installing camera base first.
A
Use short 30mm screws and anchors.
Installation Option 2:
Use holes marked with 'B' when
B
installing complete camera housing.
Use long 70mm screws and anchors.
B
A
Mounting Template
Conduit Key
Allen Key
Option 2) to mark and pre-drill the required holes.
Remove 2 of the 3 base locking screws. Use 2pc of
the 2.8" screws to mount the camera directly to the
mounting surface.
2.8" screw.
4
on page 7 to complete installation.
Option 1) to mark and pre-drill the required holes.
Remove the camera base by unscrewing the 3
base locking screws, and turn camera module
approx. 5 degrees counter-clockwise to detach
camera base from the camera module. Install the
base to the correct holes as indicated on the mount
template using the 1.2" screws. Go to step 3a.
(see page 4 for details). Remove the camera
base by unscrewing the 3 base locking screws,
and turn the camera module approx. 5 degrees
counterclockwise to detach camera base from
camera module. Install the base to the junction box
using the base attachment screws. Go to step 3a.
aligning the arrow notches on the edge of the
camera module and the camera base (label on
edge of camera module indicates the location
of the arrow notch), and turning camera module
clockwise to lock into place.
camera base to camera module.
4
on page 7 to complete installation.
-6-
INSTALLATION. VANDAL DOME
4
4) Remove camera cover by squeezing the back and front
of the cover (as indicated by the arrow indicators) at the
same time and lifting it up and away from the lens.
Arrow
5
5) Insert the included video test cable into the RCA jack and
connect to a test monitor to set up camera.
Video test cable
RCA Jack
Zoom
6
Focus
6a) Adjust camera viewing angle and secure into
screwdriver.
Note: Lens adjustment levers are by default in the
locked position. Turn counter clockwise to unlock.
Tighten levers to secure lens setting.
6b) Adjust lens and OSD as required.
6c) Re-attach the camera cover, using the thumb screw
as a guide, until it snaps into place.
7a) Re-attach the dome cover. Align arrows according to the
7
diagram below to ensure a weatherproof seal.
1
3
Correct arrow alignment
7b) Use the allen key to tighten the tamper screws.
Note: Make sure dome cover cord does not get caught in
the rubber seal.
Thumb Screw
2
Arrow on camera base
1
Arrow on camera module (inside camera)
2
Arrow on dome cover.
3
-7-