Crestron 4K DigitalMedia DMPS3-4K-150-C Podręcznik - Strona 2
Przeglądaj online lub pobierz pdf Podręcznik dla System konferencyjny Crestron 4K DigitalMedia DMPS3-4K-150-C. Crestron 4K DigitalMedia DMPS3-4K-150-C 2 stron. 3-series digitalmedia presentation system 150
Również dla Crestron 4K DigitalMedia DMPS3-4K-150-C: Z podręcznika (2 strony), Podręcznik uzupełniający (20 strony), Z podręcznika (2 strony)
Drukuj stronę
Making Connections to the Rear Panel
Make connections to the rear panel as follows:
VGA IN 1–4: Connect to RGB (VGA), component, S-video, or
composite video sources (VGA cables not included).
AUDIO IN 1–4: Connect to unbalanced audio sources
(unbalanced 3.5 mm TRS mini phone jack cables not included).
HDMI IN 1–4: Connect to HDMI
®
audio/video sources (HDMI
cables not included).
DM IN 1–2: Connect to the DM 8G+™ output of DigitalMedia™
transmitters or other DigitalMedia devices or to third-party
HDBaseT
devices (Crestron
DM-CBL-ULTRA, DM-CBL-8G,
®
®
DM-CBL, DM-CBL-D, or third-party CAT5e [or better] UTP or STP
cables not included).*
HDMI OUT: Connect to the receiving device (HDMI cable not
included).
DM OUT: Connect to the DM 8G+ input of a DigitalMedia receiver
or other DigitalMedia device or to a third-party HDBaseT device
(Crestron DM-CBL-ULTRA, DM-CBL-8G, DM-CBL, DM-CBL-D, or
third-party CAT5e [or better] UTP or STP cable not included).*
RELAY 1–2: Connect to controllable devices (cables not
included).
INPUT: Connect to a digital input, digital output, or analog output
device (cable not included).
AUDIO OUT: Connect to the receiving device using the supplied
5-pin interface connector (cable not included).
IR OUT: Connect to the included Crestron STIRP IR emitter
probe.
MIC IN: Connect to a microphone.
COM: Connect to the device to be controlled using the included
5-pin interface connector (RS-232 data communications cable
not included).
LAN: Connect to the local area network (Ethernet cable not
included).
USB 1–4 (Type A): Connect to the USB port of TT-100 Series
presentation interfaces (USB cable included with presentation
interfaces).
G: Connect to earth ground (building steel).
NET: Connect to the 4-pin NET port of a Cresnet
®
device using
the included 4-pin interface connector (Cresnet control cable not
included).
100–240V~1.4A 50/60 Hz: Connect to a 120 V power outlet using the
included power cord.
As of the date of manufacture, the product has been tested and found to comply with specifi cations for CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
Caution: Changes or modifi cations not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and receiver
DO
GUIDE
LAPTOP
COMPUTER
LAPTOP
DM-TX-401-C
LAPTOP
DO
Allow DHCP Mode or Set a Static IP Address
DHCP is enabled by default. Via the USB connection between the
COMPUTER port of the DMPS3-4K-150-C and a PC running Crestron
Toolbox™, use the Device Discovery Tool in Crestron Toolbox to fi nd the IP
address of the DMPS3-4K-150-C. If desired, set a static IP address using
Crestron Toolbox or the web-based confi guration interface of the
DMPS3-4K-150-C.
PROJECTION
SCREEN
UP
IO
SET
AUD
RGB
IN
I
HDM
HID
USB
1 -
C
E R
2 0
X -
C E
N T
D M
- T
E R
M P
U T
C O
LAN
D M
ET
MICROPHONE
RES
R
VDC
PW
24
0.75
A
I OUT
HDM
DM-TX-201-C
OUT
DM
LAN
3
2
4
AMPLIFIER
TT-100
MONITOR
TT-100
STEREO
SPEAKERS
DM-RMC-100-C
IN
DM
ET
RES
0-C
I OUT
-10
ER
UP
HDM
-R
MC
RO
LL
SET
DM
NT
CO
OM
RO
GND
DM
COM
TX
24
A MA
V
X
RX
0.75
RTS
CTS
1
S
G
IR
S
2
S
LAN
PROJECTOR
DO
Commission the DMPS3-4K-150-C System
Using the web-based confi guration interface, commission the
DMPS3-4K-150-C system by confi guring EDID, audio, video, and
DigitalMedia endpoints. In addition, use the web-based confi guration
interface to update fi rmware.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
•
Consult the dealer or an experienced radio/TV technician for help
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The specifi c patents that cover Crestron products are listed at www.patents.crestron.com.
Crestron, the Crestron logo, 3-Series, Cresnet, Crestron Toolbox, DigitalMedia, and DM 8G+ are either trademarks or registered trademarks of Crestron Electronics, Inc., in the United States and/or other countries. Apple and iPad are either trademarks or registered trademarks of Apple Inc. in the United States
and/or other countries. HDBaseT and the HDBaseT Alliance logo are either trademarks or registered trademarks of the HDBaseT Alliance in the United States and/or other countries. HDMI and the HDMI logo are either trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other
countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography
or photography.
This document was written by the Technical Publications department at Crestron.
©2014 Crestron Electronics, Inc.
DO
Allow Automatic Switching or
Manually Select an Input
By default, automatic switching of inputs is enabled. Automatic switching
causes the last connected input to be routed to the output. The AUTO LED
lights to indicate that automatic switching is enabled.
To manually select and activate the desired input, press one of the VGA
(1–4), HDMI (1–4), or DM (1–2) INPUT SELECT buttons. Refer to the
TSW-750
following table for a summary of the LED behavior of selected and
nonselected inputs.
Color
Description
The input is the active selection, and an incoming signal
Solid green
is detected.
The input is the active selection, and an incoming signal is
Flashing green
not detected.
The input is not the active selection, and an incoming
Solid amber
signal is detected.
The input is not the active selection, and an incoming
Off
signal is not detected.
NOTE:
Manual selection of an input disables automatic switching. When
automatic switching is disabled, the AUTO LED goes off.
TT-100
DO
Use the Built-In Control Program
The DMPS3-4K-150-C provides a built-in program that enables complete
TT-100
system control without requiring additional programming. Control is
accomplished using the Crestron TSW-750-B PAK 7" tabletop touch
screen, the Crestron XPanel interface, or the Apple
operations guide (Doc. 7646) at www.crestron.com/manuals for additional
information about the built-in control program.
* For all resolutions up to UHD and 4K, the maximum cable length is 330 feet (100 meters)
using DM-CBL-ULTRA cable. For resolutions up to 1080p60, UXGA, WUXGA, and 2K DCI, the
maximum cable length is 330 feet (100 meters) using DM-CBL-8G, DM-CBL, DM-CBL-D,
or third-party CAT5e [or better] cable. For higher resolutions up to 4K DCI and UHD, the
maximum cable length is 230 feet (70 meters) using DM-CBL-8G cable or 165 feet (50
meters) using DM-CBL, DM-CBL-D, or CAT5e cable. Shielded cable and connectors are
recommended to safeguard against unpredictable environmental electrical noise that may
impact performance at resolutions above 1080p.
DO
Learn More
Check the website for the latest fi rmware updates.
Crestron Electronics 15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
®
iPad
®
app. Refer to the
Product warranty can be found at www.crestron.com/warranty.
DOC. 7654A (2042246) 10.14
Specifi cations subject to change without notice.