Sharp EBR-9900SL Instrukcja - Strona 2

Przeglądaj online lub pobierz pdf Instrukcja dla Kuchenka mikrofalowa Sharp EBR-9900SL. Sharp EBR-9900SL 17 stron. Built-in kit
Również dla Sharp EBR-9900SL: Instrukcja (16 strony)

Drukuj stronę
Sharp EBR-9900SL Instrukcja
A32965,EBR-9900 O/M
1. (For U.K. use)
A cut-out w ill have to be provided in the side of the kitchen cabinet for the plug of the oven.
N.B.The m ains plug m ust be accessible after installation or an all-pole sw itch disconnection m ust be
provided w ith a contact separation of at least 3 m m in each pole.
(For Continental use)
The electric outlet m ust be installed at 150 m m high from the floor of the built-in cabinet and at 50 m m
from the right w all of the built-in cabinet as show n in Fig. 1. The m ains plug m ust be accessible after
installation or the oven m ust be connected to an electric circuit provided w ith an all-pole sw itch (contact
gap no less than 3 m m ) to disconnect the oven in case of danger. A safety-device like a fuse in the
installation m ay be used as a sw itch.
2. Rem ove the built-in kit from the package.
3. Set the spacing brackets 1 on the shelf along the right and left w alls of the kitchen cabinet, adjusting
the front ends of the shelf and the spacing brackets, and attach them w ith the four screw s
show n in Fig.1.
Caution:
4. Place the exhaust duct 2 on the ceiling of the kitchen cabinet along the back w all of the cupboard D and
left w all of the kitchen cabinet w ithout the clearance as show n in Fig.1 and 2. Secure to the ceiling of the
kitchen cabinet w ith tw o screw s
5. Rem ove the backing paper from the cushion 6. Attach the cushion 6 to the edge of the exhaust duct
3 as show n in Fig. 4.
6. Insert tw o tabs of the exhaust duct 2 into the slits of the exhaust duct 3. And fold the tabs.
7. Rem ove the screw E from the oven as show n in Fig. 5.
8. Let the power supply cord pass through the hole of the lower side of the intake duct 4 as shown in Fig. 6.
9. Install the intake duct 4 to the rear of the oven w ith tw o screw s
in Fig. 6.
Caution:
10. Install the intake duct 5 to the rear of the oven w ith three screw s
Caution:
11. Rem ove the backing paper from the three cushions 7, 8 and 9. Attach the cushion 7 at the left side along
the intake duct 4 then attach the cushion 8 at the top of the intake duct 4, and along the left side of the
cushion 7 and the oven as show n in Figs. 8-a and 8-b. Attach the cushion 9 to the top of the oven as show n
in Figs 8-a and 8-b.
12. (For U.K. use)
Place the oven on a table/stand positioned in front of the kitchen cabinet. If you do not prepare the table/
stand, tw o persons are required. One to hold the oven w hilst the other feeds the pow er supply cord
through the prepared cut out.
(For Continental use)
Place the oven on a table/stand positioned in front of the kitchen cabinet.
If you do not prepare the table/stand, tw o persons are required. One to hold the oven w hilst the other
connects it to the pow er supply.
13. Connect the oven to the pow er supply.
Caution: a. In U.K., connect the oven to the pow er supply 230-240 V, 50 Hz.
14. M ake sure the oven is on the spacing brackets on the shelf of the kitchen cabinet. Then adjust the position
of the oven so that the feet of the oven are fitted into the recesses of the spacing brackets as show n in
Fig. 2.
Caution:
15. Place the built-in fram e elem ent
horizontally. Secure loosely to the kitchen cabinet w ith tw o screw s
16. Insert tw o built-in fram e side elem ents
And secure tw o screw s
and left built-in fram e side elem ents
Note: Fit the hole of the built-in fram e side elem ent
17. Install the second built-in fram e elem ent
oven. And secure the built-in fram e elem ent
to the kitchen cabinet w ith tw o screw s
Caution:
Downloaded from:
http://www.usersmanualguide.com/

INSTALLATION INSTRUCTIONS

The arrow m arks on each spacing bracket should be pointing tow ards you.
B from below as show n in Fig. 3.
Avoid pinching the pow er supply cord betw een the oven and the intake duct 4.
Avoid pinching the pow er supply cord betw een the oven and the intake duct 4.
b. In the Continent, connect the oven to the pow er supply 230 V, 50 Hz.
M ake sure that the pow er supply cord does not touch the air vent openings behind the oven.
0 on top of the oven m aking sure that it is level both vertically and
A betw een the built-in fram e elem ent 0 and the kitchen cabinet.
D tightly as show n in Fig. 9. Check location by m easuring distance betw een right
A . The distance is stated in Fig. 10.
D as show n in Fig. 9.
M ake sure that 15.5 m m of the fram es (upper and low er) and cabinet overlap each other as
show n in Fig. 11, or the kitchen cabinet door m ay touch the built-in fram e elem ents.
C and E (rem oved at step 7) as show n
C as show n in Fig. 7.
D as show n in Fig. 9.
A to the screw D w hen inserting.
0 over the built-in fram e side elem ents A at bottom edge of the
0 through the holes of the built-in fram e side elem ents A
2
B , as