Sharp AR-LC6 Instrukcja serwisowa - Strona 12
Przeglądaj online lub pobierz pdf Instrukcja serwisowa dla Wszystko w jednej drukarce Sharp AR-LC6. Sharp AR-LC6 20 stron. Digital copier/printer/ multifunctional system option large capacity tray
[6] ADJUSTMENT
Each adjustment item in the adjustment item list is indicated with its JOB number. Perform the adjustment procedures in the sequence of Job numbers
from the smallest to the greatest.
However, there is no need to perform all the adjustment items. Perform only the necessary adjustments according to the need.
Unnecessary adjustments can be omitted. Even in this case, however, the sequence from the smallest to the greatest JOB number must be observed.
If the above precaution should be neglected, the adjustment would not complete normally or a trouble may occur.
1. Setting item list
Job No.
ADJ 1
Print off-center adjustment
ADJ 2
Resist amount adjustment
2. Details
ADJ 1
Print off-center adjustment
1) Set the print off-center adjustment mode of SIM 50-10 by the key
operation of the machine. (Press the keys as shown below to enter
SIM 50-10.)
∗
∗
#/P
C
5
2) In SIM 50-10, the display is shown as follows. The print off-center
adjustment value can be set for each paper feed tray.
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. SELECT 0-9, AND PRESS
START.
0.TRAY SELECT
1
1.COPY START
2.MAGNIFICATION
100
(ADJUSTMENT DATA)
3.TRAY1
50
4.TRAY2
50
5.TRAY3
6.TRAY4
50
7.BPT
50
8.LCC
Adjustment position
Display
Item description
item
TRAY1 TRAY1
Print off center
adjustment position
TRAY2 TRAY2
Print off center
(LCC left
adjustment position
side)
TRAY3 TRAY3
Print off center
(LCC right
adjustment position
side)
TRAY4 TRAY4
Print off center
adjustment position
MFT
Manual
Print off center
paper feed
adjustment position
LCC
Large
Print off center
capacity tray
adjustment position
ADU
Duplex
Print off center
adjustment position
(ADU)
Adjustment item list
ADJ 2A
ADJ 2B
0
1
0
2
50
50
9. ADU
50
Set value
Set
Default
range
50
0 to
Shift by
99
0.1mm for
set value 1
AR-LC6 ADJUSTMENT 6 - 1
Adjustment in the resist amount adjustment mode
Adjustment in the print lead edge adjustment mode
3) Select "0: TRAY SELECT" and press START key.
The display is shown as follows. Select "6: LCC" as the paper feed
tray, and press START key.
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. SELECT 1-16, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT
6.LCC
(ABOVE+10: DUPLEX MODE)
4) The display is shown as follows again. Select "8: LCC" and press
START key.
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. SELECT 0-9, AND PRESS
START.
0.TRAY SELECT
1
1.COPY START
2.MAGNIFICATION
100
(ADJUSTMENT DATA)
3.TRAY1
50
4.TRAY2
6.TRAY4
50
7.BPT
50
5) Then enter the adjustment value with 10-key.
(Default: 50, Adjustment range: 0 – 99)
• When the adjustment value is decreased by 1, the image is
shifted to the rear side by 0.1mm.
• When the adjustment value is increased by 1, the image is
shifted to the front side by 0.1mm.
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. INPUT VALUE 0-99, AND
PRESS START.
8.LCC
6) Enter the adjustment value and press START key, and printing is
started and the set value is stored.
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. NOW COPYING.
7) Check the printed self-print result, and repeat procedures 5) – 6)
until the value is in the range of 0 ± 3mm.
When the value is in the above range, press CA key to terminate
the simulation.
(Rear side)
a
Print lead edge
b
(Front side)
(Print back surface)
Simulation to
be used
1
2
50
5.TRAY3
50
8.LCC
50
9. ADU
50
50
Adjust in the range
of the figure
(0 ± 3mm).
50-10
51-2
50-5