Sharp FO-DC600 Dodatek do instrukcji serwisowej - Strona 2
Przeglądaj online lub pobierz pdf Dodatek do instrukcji serwisowej dla Wszystko w jednej drukarce Sharp FO-DC600. Sharp FO-DC600 8 stron. Facsimile
Drukuj stronę
FO-DC500U
FO-DC600U
1. Specification changes
No.
1
REPORT key operations modified
2
Max. scan length changed: 19 to 38 inches
3
Display thumbnails of attachments to Transaction Report
4
Line monitor added
5
Fax Transfer function added
6
PC FAX function added
7
Multicast transmission function added
8
Insertion of separate page when network printing
9
Activation switch added for activating new functions
2. Soft switch changes
SW
DATA
NO.
NO.
SW9
8
Action when RTN received
4
Line monitor up to Phase A
SW22
5
Monitoring dial signal up to Phase A
1
Reserved
2
Reserved
SW60
3
Reserved
4
Reserved
SW66
7
Maximum size of input document
SW68
3
Image length of TX transaction report
SW78
4
Criterion of resolution when receiving
6
Transferred fax image
SW86
7
Insertion of Adobe's URL into E-mail
SW90
1
Method of detecting CI frequency
3. After upgrading FLASH ROM
After upgrading from version TA69D or earlier to TA69F (Sep. version) or later on FO-DC500, or after upgrading from version TA70C or earlier to TA70E
(Sep. version) or later on FO-DC600, perform the following to activate the functions 1, 2, 3, 5, 6 and 7 in "Specification changes".
Go through MENU → 9 →
to perform upgrade.
* After this operation, the bit is set to "1" for soft switches SW60 No.1-No.4, SW66 No.7 and SW68 No.3.
* When there is no data to save, clear the memory after upgrading. Settings return to the default and the specification changes above become effective.
4. Connection between network option and FLASH ROM version
FO-DC500: TA69D or earlier
FO-DC600: TA70C or earlier
FO-DC500: TA69F or later
FO-DC600: TA70E or later
(*1) : Existing functions are supported and none of new functions are.
(*2) : PC FAX cannot be used (additional software will be made available on the Web by U.S.A.)
(*3) : See the attached manual for the printer driver installation procedure.
Description
ITEM
→ 8 → # → 7 → START to enter the diag mode. Then holding down Z key, select "Upgrade Setting" and press START
FO-LN1
Manufactured in or before Aug.
O
X(*2)
Purpose
Functionality improvement 1-3
Functionality improvement 1-1, 1-4, 2-21
Functionality improvement 2-21
Functionality improvement 2-14
Functionality improvement 2-20
Functionality improvement 2-20
Functionality improvement 2-20
Functionality improvement 2-21, 2-23, 2-32, 2-33 2-21, 2-23, 2-32, 2-33
Service
Switch setting and function
1
Handle to no error
On
Monitoring fax signal and dial signal Monitoring fax signal only
38 inch
Reduce image of whole 1st page
Millimeter
Printed at transferred error only Printed every time
No
Firmware
Manufactured in or after Sep.
Manufactured in or before Aug.
X(*1)
O
– 1 –
Corresponding page in service manual
FO-DC500U
2-2, 2-6
0
Handle to error
Off
19 inch
15 cm image from top of 1st page
Not specified
Yes
Modem
FO-NP1
Manufactured in or after Sep.
O
∆(*3)
FO-DC600U
1-3
1-1, 2-21
2-21
2-14
2-20
2-20
2-20
2-2, 2-6
Initial
Remarks
setting
0
Change
0
Addition
0
Addition
1
Change
1
Change
1
Change
1
Change
1
Addition
1
Addition
0
Addition
0
Addition
0
Addition
0
Addition
∆(*3)
O